Search results for query: *

Carlisle’s coming up soon. I’m sure you can find one there.

Small Block MOPAR & LA 318-360 – Single Charger | TorqStorm

[FOR SALE] - CAT Small Block Gear Drive - New

[FOR SALE] - Original Mopar A Body 8 3/4 Rear End Housing (From Canada) Eh!

Quite some time ago I mailed a set of those gears to @63spf (Chris), idk if he still has them available. Perhaps send him a PM.

A500 OD spring stuck in Hub?? I don’t know if this helps but, perhaps this FMJ member will part with his case.

You can do an ISO Delete many ways. Use a washer ( I believe 1 5/8” OD) under the spring pack bolt to center the axle perches.

[FOR SALE] - Offy 2x4 Intake Many people convert these dual quad intake manifolds to blower manifolds.

ICON Forged Piston - Chry 408 Rod 6.123 Step Dish +34cc 2V Boost friendly pistons......

U want just the AGC 15, or all of these?

I'll go thru these at work

FMJBodiesOnly member Slant6Billy has a couple of rear ends, 8.25 and 8.75. He is in NJ.

Pulley configurations can be challenging. eGag has pulley spacers that can be ordered with a 2.25" female register (on one end to mate to the harmonic balancer) and a 2" male register on the other end. Vee pulleys and 6 rib serpentine pulleys are readily available. All of these are stackable...

You can always surf eGag for a complete blower setup intended for a chevy. Adapt that setup to a sb Mopar using an Indy ModMan intake manifold.

Bill Laney of Max Wedge Performance located in Australia casts several sb Mopar blower intake manifolds. He definitely has made 671 for standard and W2 heads. He also casts them for the B&M 144/162 blowers, maybe even 174 units as well as Weiand units too. Here's a pic for a standard sb Mopar.

I'm just South of you, I have a 489 case with adjusters and both retaining clips.

LB distributor will have two pick up coils and two wire connectors instead of one.

I have several Mirada fans.

Dodge Mirada rolling chassis, caged, 4 link 9" rear, set up for BB Mopar can deliver.

I traded my shortbed for a longbed someplace in Lima Ohio, IDK the guys name or phone number but I did find it on ebag. It was on Bellefonaine Rd/ rt 117. He had ALOT of beds. All makes and sizes, i will look for the info.

Google, Bill Laney Max Wedge He has blower manifolds for small block Mopars, almost any combo you can think of. 6-71/ 144/ 162/ and has 6-71 for standard or W2 heads. These are one piece cast aluminum manifolds made in Austrailia. Big bucks but are of a very nice design and quality. The...

I have a complete Dick Landy, B+M 174 blower setup for a small block Mopar. I am working on an 8-71 setup for a stroked 360.

I got them both!!

I think it has 2 screws that bolt thru the dash. Once the dash cover is removed, its the two screws on the right by the pass side speaker. The chime is located behind the glove box. I will check tomorrow, if u dont hear from me... Send me a PM to remind me!

I got a headlight switch. Where is the "chime" located? (on the fuse box?) I can check the FSM if needed.

I got a 52 1/2" driveshaft out of a 78 Volare 6cyl. Im assuming it had a 904 trans with a 7 1/4" rear. Located in 11783

Weiand Part #1995

I have a Weiand 1995 Tunnel Ram for sale. I only used this for mock-up.