Search results for query: *

I have decided to sell my 72 scamp. I originally bought it to daily drive and I did daily drive it for a while. It is capable of long trips and runs extremely reliably. Before I bought it, it sat under a redwood tree for maybe 10 years. The first thing I did was strip off the vinyl top and...

Looking to make a couple mods on my 01 ram with the 5.2 mag. Stupid California isn't letting non factory tunes anymore so anything too radical won't be considered. Was looking at a comp 20-746-9. I know its not an a body but this forum is the best Mopar resource I know of.

Looking for a big block fuel pump, rebuildable type. Let me know what you have.

Ok, a question for all the avs masters out there. I've got a pretty virgin looking 4966s avs and the secondary spray bars are different from one barrel to the other. Is this typical? One has one large hole on the end nearest the throttle blade and 2 larger holes at the top. Then the other spray...

Got home on a rainy night and thought the exhaust had a nice tone to it. Factory exhaust pipe, stock looking muffler to a 1.5" tail pipe. Engine is stone stock, even still running points. Didn't have anyone to hold the phone so no revving.

In search of a 3 speed motor or parts to make mine work. My motor has stripped out the big white plastic gear, so I could always use a motor that burnt out or other part that went bad. Looks don't matter. It's for my 72 beater daily driver.

Looking for a one fender mounted turn signal and one front left fender marker lamp. Let me know what you have.

Just got done doing new valve stem seals and setting the valve lash when I decided to play with the jetting a bit. I noticed that the motor just didn't have that spunk that it should have off idle and when you would mat the throttle. I went through the carb when I first got the car, and found...

$15 + shipping for this bbd. Came off a running 318. Was a rebuilt unit. Had a slight mishap with the chain on the engine hoist a d bent an ear for the air cleaner mount. So it's being sold for parts. If it doesn't sell it goes into the scrap pile.

Yes, they are brand x. And... Wow. Worse shrouding I have ever seen. Would unshrouding the intake valve help or hurt this cyl head? I guess they were shooting for some type of swirl and quench but what the hell were they thinking? That wall is right up against the valve and is close to .200" not...

Need a good dipstick tube, would rather get a good original than a cheapy me gasket one. Let me know what you have.

I was digging though my stash of cams for a spare parts build and found an odd one. I could visually tell the lobes had quite a bit of lift so I didn't even bother but I did throw it in the v blocks to get some specs on it. Looks like it's a 250/245 duration at .050" tried to get duration at...

Slant six 904 out of a 65 dart. Pulled for v8 swap. Looks to have been rebuilt pretty recently before it was pulled. Fluid bright red and clear. It was driven into the shop before the swap. It's been sitting in the corner for 5-6 years now and needs to go. First $100 gets it. Located in Vallejo, ca.

Building a extreme budget turbo 318, almost all of the parts will be parts on hand from other builds with the exception of gaskets and consumables. This motor will be replacing my high revving 350ci 340 that is in my 66 b-body ( I know, but small block stuff isnt too hot on the b body forums)...

Just noticed one 2 different sets of rocker shafts, the oiling holes and orientation notches are completely different. Whats up with this? Seems like the rocker shaft on the right is drilled completely wrong as the wear pattern is completely offset from the oil hole. Could the shaft on the...

I've got a pretty mild solid roller 340 and a few different set of rockers i can run on it. The cam is a comp 288r solid roller. Currently it has a set of 1.5 harland sharp full rollers on it, one adjuster snapped and that led me to find out the roller tips are also out of round and the shafts...

Looking to quiet down my ride. It's currently a 350ci 340, 10.5:1 compression, p&p j heads, 4 speed, hooker super comps, 3 inch exhaust, x pipe, 2 chamber mufflers, to full tail pipes out the back. I'm thinking of using the large case 3" super turbo's to quiet it down alot. Only thing is that...

I'm looking for a nice driver quality 4 door or wagon. Would prefer 67-72 a body or 66-72 b body. Let me know what you have. Thanks!

Looking for an EFI intake to fit LA heads. Let me know what you might have.

Cracked open a pretty virgin looking 318 today. Found out that it has a forged crank in her. Does not look to have had the bottom end rebuilt, bearings have 68 date codes, has silent type cam chain, stock bore, and cast pistons. Busted open lots of 318's and this is the first i've seen with a...

Got a pair of rocker shafts, one pair is obviously not right. The set on the left came out of a 68 340 and the set on the right out of a 66 273. You can see the feed holes on the left pair are drilled correct and in the middle of the wear area. The set on the left has the holes drilled...

Looking for a cheap small block. Finally decided to pull my 340 to detune it and throw a mild small block in it while I do that. Anything will work, 273, 318, 360, 5.2, or 5.9 mag. Located in the San Francisco bay area.

Was driving to work when i felt the 340 go down a cylinder and at a stop light i could really hear it tapping away. At first i thought one of the solid roller lifters took a massive dump but when i pulled the valve cover i found: harland sharp wants around 50 bucks for 4 adjusters...

This is a small block aluminum bellhousing with the 4.8" retainer bore for the hemi/440hp a833 or a od trans with a turned down retainer. Great way of running an 18 spline transmission behind your small block or easy way of running an OD a833. Its a bit dirty but in excellent condition with no...

I have an exceptionally clean 4966s AVS carb for sale, probably doesnt need a kit, but i would throw one in for good measure. Perfect for a small block. Located in Vallejo Ca Asking $115 shipped in the US.

1978 d150 adventurer club cab survivor factory 360 4bbl/thermoquad with 727 9.25 rear with suregrip and 4.10 gears working dual fuel tanks truck was garaged for most of its life, interior is near perfect, has am/fm radio, rear jump seats, full gauges with vacuum gauge and volt meter. exterior is...

This is my customers engine after he got it back from the body shop. Says it was fine when he dropped it off.... Number 6 conrod is so messed up it will no longer fit through the bore, was a nice engine, headers, cam, 4bbl manifold. Block is already .060'' over.

Got an old solid flat tappet cam that i found, the cam card specs are 296/300 @ .012" 250/244 @ .050" .375"/.344" Lobe Lift .017"/.018" Hot Lash w/1.5 rockers 105 LSA that would this cam be good for? Seems real weird on the duration and lifts. Its also got a real tight lsa. Would probably...

I have an exceptionally clean 4966s AVS carb for sale, probably doesnt need a kit, but i would throw one in for good measure. Perfect for a small block. Asking $130 shipped in the US.

http://sfbay.craigslist.org/nby/cto/4390939135.html :violent1::violent1::violent1: