Recent content by Cuda340

  1. C

    [WANTED] 1967-69 Front fender patch panels for the front lower sections of the fenders

    WTB: 1967-69 Front fender patch panels for the front lower sections of the fenders. I know they make the rear lower sections of the fenders, but I have not seen the front lower sections listed. So, I am assuming that if you have a pair of rotted fenders that this section could be cut off. This...
  2. C

    My 1st 833 rebuild

    Get a piece of 3/4" conduit to make a dummy shaft for the cluter gear, and get some trans assembly goo, especially use this to hold in the rollers in the cluster gear.
  3. C

    Small Block 727

    I have a 904 completely built with an 8" convertor, shifter, temp gauge, cooler, etc. Went to four speed and have all the items. let me know if interested. Thanks, Jeff [email protected]
  4. C

    how to tell what a-833 i have

    Yes you can use the tail and main shaft and swap them out.
  5. C

    Question on 69 cuda tail panel clips

    I bought mine from R/T Specialties. Look in any of the mopar mags he advertises there. Jeff
  6. C

    18 spline from a 23 spline?

    The numbers on the side will not tell you if it is an 18 spline or 23 spline. You have to physically look at the input shaft to tell. Take of the inspection cover and look up at the shaft. The 18 spline is noticely larger than the 23 spline.
  7. C

    Engine Colors Need Help

    here is my turqoise engine
  8. C

    Needed: 1969 Barracuda Tail Light Bezel Passenger Side

    Looking for a 1969 Barracuda Tail Light Bezel Passenger Side in good shape meaning no pits or cracks. I can get it rechromed if needed. Thanks, Jeff [email protected]
  9. C

    PST strut rod bushings?

    There are the two piece design ones (later improved design) and the one piece design ones. I just went through this myself on my 1969 'Cuda. I ordered the PST kit as well. I didn't use the one piece ones they give you in the kit, I bought the Moog K7040 kit. A little more expensive but worth it...
  10. C

    1969 'Cuda Owners I need lower body stripe information

    Does anybody own a 1969 'Cuda car A56, A57, or A13? I need some lower body stripe information. Dimensions and such. Thanks, Jeff
  11. C

    833 reverse pops out (1st post on board)

    I agree....
  12. C

    1969 'Cuda 340 Lower Body Stripe Application

    Thanks for the info AdamR... The question now is where do I get a set in good shape or how are the repo's??????
  13. C

    1969 'Cuda 340 Lower Body Stripe Application

    I was wondering if anybody has the exact placement dimensions for the lower body stripes on a 1969 'Cuda 340. I am looking to put them on my car and I wanted to know where they go and how difficult they are to put on. I already have the hood accent stripes but I wanted the lower stripes. Also...
  14. C

    A-body Strut Rod Questions????

    Are all A-body Strut Rods the same? I have a 1969 Cuda and one of my strut rods was bent. So I got another pair off of a 1971 Duster. They should be the same correct? There is a little difference between the two when I put them up next to each other. First the threads on the 71 are course and...
  15. C

    A-body Idler Arm Question?

    http://www.rockauto.com/ref/Moog/Detail2.html?cds.demo.activant.com/C2C/U2L8/33/334500/100/K7042_TOP.jpg Here is a pic of the kit I got. Where does that metal washer go?
See more
Back
Top