Teener before-
after
before
after
after
before
after
Show off your small block.
- Thread starter toolmanmike
- Start date
-
Mopar118
Active Member
I don't know. I do know, however, that it's not a standard A body color.
Demon540
Well-Known Member
Your going to have a hell of a time putting those heads on that block!
mario03srt
Well-Known Member
All,
Here she is All complete! A little more wiring appearance cleanup to be done.
367 cubes of Fuel Injected Fury!
FiTech Injection, Indy/RHS X heads, Comp XE 274 bumpstick, 10.2-1 w/ Speed Pro Coated 116CP flattop slugs, GM HEI, Hooker Super Comps, Eddie Air Gap Manifold.
Not perfect but pretty clean and runs out great! Have about 300 miles on it.
Thanks,
Marion
Here she is All complete! A little more wiring appearance cleanup to be done.
367 cubes of Fuel Injected Fury!
FiTech Injection, Indy/RHS X heads, Comp XE 274 bumpstick, 10.2-1 w/ Speed Pro Coated 116CP flattop slugs, GM HEI, Hooker Super Comps, Eddie Air Gap Manifold.
Not perfect but pretty clean and runs out great! Have about 300 miles on it.
Thanks,
Marion
LJ67barracuda340
Well-Known Member
up date on inlet air temps with my cold air system,,,,.
nice day in Ontario on Dec 1 so we went out for an exhaust test.. engine temp was 186*F and FITech read the air temp at the throttle body as 57*F.
fasttcars
Member
Strong running 365 in my valiant. First car I built when I was 18 and still have 22 years later.
QuickDart360
Well-Known Member
Hey fasttcars can you share what color is your car? That color is very nice!! Also mind sharing cam and other specs of that beautiful machine, please?
SPACECOWBOY
Well-Known Member
Updated car
Last edited:
MileHighDart
Well-Known Member
My fresh 5.9 Magnum.
SWED67barracuda
Well-Known Member
.030 over 318 . forged bottom , domed KB pistons , 2,02 J heads , 268-276 Woodo cam .
'Cuda_ragtop
Woulda, Shoulda, 'Cuda!
SWED67barracuda
Well-Known Member
Thanks . I think so too . It`s going in a 67 notchback.
douglas340
Well-Known Member
It's not in the car. heh
'74 318 block if memory serves.
Offenhauser 5488 for early 273, need to either get some angled shims or mill the intake bolt flange angle.
302 heads with 1.78" 1.50" valves. will go on the 318 that is currently in the car, not on this build. Just mating everything up to check the intake manifold bolt angles.
Mallory 4757901H dizzy on shelf out of picture
ductile iron 1.5 rockers
Doug's D452 headers on shelf
timing chain cover
Just collecting parts and stacking them up.
still need;
water pump
gaskets
rotating ***'y
bearings and freezeplugs
oil pump
solid flat tappet cam
rocker shafts
milodon timing gear
harmonic damper
oil pan
windage tray
oil pump shaft
carbs
nuts, bolts, studs
orange paint
'74 318 block if memory serves.
Offenhauser 5488 for early 273, need to either get some angled shims or mill the intake bolt flange angle.
302 heads with 1.78" 1.50" valves. will go on the 318 that is currently in the car, not on this build. Just mating everything up to check the intake manifold bolt angles.
Mallory 4757901H dizzy on shelf out of picture
ductile iron 1.5 rockers
Doug's D452 headers on shelf
timing chain cover
Just collecting parts and stacking them up.
still need;
water pump
gaskets
rotating ***'y
bearings and freezeplugs
oil pump
solid flat tappet cam
rocker shafts
milodon timing gear
harmonic damper
oil pan
windage tray
oil pump shaft
carbs
nuts, bolts, studs
orange paint
abodyjoe
Well-Known Member
the latest toy..
I like the looks of those rockers.
Very nice!
aaronk785
Well-Known Member
and.... 3 hours later....
skrews
Well-Known Member
-
