Search results for query: *

Not a lot you can do on a small block. Try a heavier oil and perhaps put a aftermarket oil pressure gauge on your car so you can see how bad it actually is. You do not need a lot of oil pressure at idle but you need some!

I just remove the Heads. Really not a very big job and save my nerves!

I would use it. I would not think twice.

How round the cylinder is makes a hell of a lot more an issue with ring seal than a thou or two in the ring gap does at least in our shop!

We have a bunch of chickens and I have noticed = Even a Blind Chicken gets a lump of Corn every now and then!

We ever since I Epoxy Painted the shop floor it is too slippery for those Waders! I am afraid I might Hone Myself a new one.

Yep! I think you might very well might be for a street car.

On our race engines (Especially Small Block Mopars) not only do we use a Deck Plate but we home the blocks at the water temperature that we actually stage the race cars at. Does it make a measurable difference? I do not know but we sure do get our feet wet a lot and go thru a lot of Socks.

The Air Gap Intake does a pretty good job of keeping the carb cooler by itself. A 1 inch phenolic spacer should fit under stock Hood with room for a decent size Air Cleaner.

Wanted W2 headers for B/E/F Body Mopar (One # for all these) OR A Discount code to buy them new.

I understand there is a fresh code out now. Does anyone know about it?

it looks great to me as Well!

Not unusual for my engines to have some noise the first minute upon startup with the clearances I run on the skirt. Now if it lasts longer than that or sound like someone has a hammer inside = that is a significant concern. How much piston to wall clearance on the skirt 90 degrees opposed to...

Lots left!

Plenty left!

Well I can not guarantee that it will make you run 150+ But you will look like you might! Offers Considered?

Thanks! I bought them all.

No racing at our LVMS track at all in May. They have the Electric Daisy Festival where they draw 100,000 Hippies = Screaming and Naked! The tell me they make more money on that than all the drag racing events the entire year! The trash cleanup and removal of all the comatose bodies takes...

Do you have a 130 /143 tooth flywheel? There is a 172 tooth ( I think that is accurate ) for a non gear reduction starter that the pitch of the gear may cause the starter to stick in engaged position.

No Oil pressure reading is fine. Oil only goes to rockers in a few certain positions of the engine rotation. Rotate it a bit at a time as Myron said in post #2. He knows these engines as well as anyone I know!

I would have a concern with cutting the mains down over .300 on a 360 cast crank. I would also be concerned with the opening up of the 318 block to 2.810. It would be quite a machining job for me and it would make the skinny 318 Main caps even skinnier yet. I have seen a 360 stock eliminator...

The 360 has a much bigger Main bearing size! As I recall it is 2.81 The 318/340/273 has a much smaller Main Bearing size. As I recall 2.50 You can buy longer stroke cranks with the 2.50 Main size. A 4 inch would get you 391 CI as I recall. The 408 converted 360 is a good combo! The main caps...

Can you unbolt trans crossmember and lower transmission tailshaft enough to get a allen head socket with a extension on it. Or cut a couple small holes in floorboard and replace them with a plate to get from drivers area. Someone beat my post by a few seconds!

This hood held up well @150MPH+ on Pinks All Out! It is a solid well built piece.

Burp

Burp

I am having way more fun than a 76 year old Guy usually does! For years I raced out of Bob Mazzolini's Shop and he gave me a shirt that said "How much Horsepower can I have and still go to Heaven?".

They were sold but when I measured them I had the calibers in the valve relief pocket. they are actually 1.73 to 1.74 probably closer to 1.740. I may have the rods = I have a 5000' shop that you can barely walk thru that is two stories. Also Six smaller shops full of parts and a dozen...

On my engine I ran Hemi length custom rods I will remeasure everything in a day or two. I wrote on top of box 440 with 1/2 inch stroke I cut the deck some but i do not remember how much. The Hemi rods are about .100 Longer ( I do not remember anymore )?

I am confused = I will measure again tomorrow or Thursday.