Search results for query: *

If anyone's interested, would let this go for $205 shipped to the lower 48. "This is the rear, aluminum finish panel that was on my 1968 GTS. The previous owner painted it black for whatever reason. All mounting tabs are there, though some are bent. The are right around the keyhole looks...

Looking for a water pump housing for my 383, If you have one with a working water pump that's even better. Thanks

Looking for a good front windshield gasket for my 69 Dart. Any help would be appreciated. Thanks!

I have a 1969 Dart GTS 383 with the original KFrame and motor mounts. The engine I have that runs is a 1969 B Body HP 383. What motor mounts are available for this application? Thanks in advance!

My father in law is letting me use his old Miller Cricket 115V Mig for some welding I need to do on my car. He told me he always wished it was a gas welder, much cleaner welds obviously. I was wondering if there is a way I can convert this to use some sort of argon gas for him? Any help...

I have a set of pistons that I believe to be for a standard bore 340. Is there a way to verify this? Any marking I should look for. Thanks in advance.

I'm looking for the length and width of the body on the 67-69 Darts. I'm trying to plan out what I'm going to need for a make-shift paint booth in my back yard. I don't intend anyone to go measure, I can do that if it comes down to it. I was just wondering if someone had already taken these...

I'm just wondering if there's any way of verifying if a car came with sure grip or not without the broadcast sheet. Also, is there a way to identify the original gearing of the rear? Is there a breakdown somewhere of what codes typically show up on the fender tag compared the broadcast sheet...

Looking for a 1969 Dart Thumbwheel Radio. I'm going to gut it and see If I can interface it with my ipod. So the cheaper the better. It just has to look nice on the outside and I need to be able to push the buttons and turn the wheels. Thanks

Looking for the mounts to get my 383 onto a spool kframe. Thanks!

I have a 383 I'm putting into a 69 Dart and I think these are 2 of the last pieces I need. If someone has an alternator or big block pitman arm let me know. Thanks!

Looking to buy as stated, the 4 speed shifter boot and ring for a 1969 Dart. If you can part with one please let me know. Also if someone has the 4-speed top plate for a console, or an auto one for real cheap that I could cut for a 4 speed that would work too! Thanks.

Looking for a decent drive shaft for my '69 Dart, it's a 383 that I'm converting to 4 speed. Let me know if you have something that will work, Car is pretty much stock.

What's the difference in the console body between the auto and the 4 speed console? I can see the difference in the plate, but I cant really tell the difference in the body. There must be though, based on ebay selling prices anyway, I would hope there is a difference. I have 2 Auto...

I have real nice bumpers on my car but the previous owner decided to spray paint the car right before I bought it and never masked the bumpers so there is tons of overspray on them. Is there a way to remove the paint without ruining the chrome?

Ok guys, I hope this can be fixed pretty easy. When Taking out my seats today I guess I pulled a little too hard on the rachet and snapped a bolt in half from under the seat bracket, the one that goes through the floor. Anyone know of an easy fix? Or if it's not an easy fix, then any...

Does anyone know where I can find a rebuild kit for the Carter AVS 4226S. I know they were bought by Edelbrock, just wondering If I can just ask them for the kit or if there's another way to go. Also, I've heard of a strip kit for the Carters that used to be around. Can anyone give any...

I'm looking for a set of covers that I can use while I'm working on the car this spring, Don't want to put the chrome ones on yet. Any condition will work as long as they're solid and I can seal them. The cheaper the better!

I dont know if this has already been covered, but I'm always on this site and haven't seen much talk about it. Anyway, Mancini Racing has the 68-69 unsilenced 340/383/440 Air Cleaner with wrinkle finish back in stock! I didn't believe it so I ordered one expecting to get the same "sorry...

I am looking for any oil pan for a 69 dart 383. I would like an original A-Body oil but i was told the 187 pan would work as well and is from a CBody. A couple dings are ok, but no major dents or rust. Let me know what you have.. Thanks. Also Still looking for: Trunk Finish Panel For...

I figure someone here can help me out. I am trying to figure out when my car was built and if the engine i have is age/type appropriate. The car is a 1969 Dart 383. Sequence number 191783 (from broadcast sheet, not VIN). The engine is a 383 HP Cast 12/18/1968. And I have no clue where...

I'm looking for a decent seat of seat covers for a 69 Dart GTS without head rests. Seat covers do not need to be correct pattern, just must be the black vinyl material. Does anyone have a seat they bought and changed their mind on? Or know where I can get a set reasonable? When the car's all...

Looking for a good pair of 383 exhaust manifolds for a 69 Dart. Must be either from a B-Body or A-Body. Let me know what you have. Thanks

This is going to be a tall order but I'm looking for exhaust manifolds for a 69 383 DART. I think Casting numbers should be 2863000 or 2863900 for the passenger side and 2946720 for driver side. Also looking for a big block bellhousing for 10 1/2" Clutch. Looking for a good trunk finish...

Just picked up a real nice 383, or what I hope is a nice 383 anyway. We'll find out soon I guess. I want to mate it to the A-833. I have a few questions for all the brains at this place. What bellhousing do I need? Will my driveshaft work with this? It has an oil pan, but not from an...

Just checking if there is any interest in this car. I was going to put it together and drive it while i work on a gts, now work's taking all of my time so I can realistically barely work on 1 car. If it doesn't sell it might end up giving most of its life to the gts which I really do not want...

Looking for Black Bucket Seat Covers and/or Foam. No head rest. Thanks in advance.

I've got 2 cars I'm trying to restore, one is a 1969 Dart Swinger 340 that many of you have helped me get parts for. I'll have to get a list together of everyone that has helped and list some praise. I have been studying for my FE exam and putting in all kinds of hours at work lately so...

How do you identify the BBody Pistol Grip that is used for the dart? Ha, I asked the question before I searched. Looks like it's already been answered. Thanks, and IF a MOD can delete this post that would work.

I have 2 project cars, one i'm trying to finish by Fall and the other is probably a 5 year project for me. The one that's going to be a long term thing is pretty rough and I was thinking of replacing full floor with rockers, rear frame rails, and passenger inner fender. The frame rails are...