Search results for query: *

New reproduction battery tray for an early a body Dart, Valiant or Barracuda. $30.00 FREE SHIPPING to lower 48!

273 Early A Body Transmission extension with new gasket: $50.00 + shipping. Bellhousing was not as described and linkage is gone.

Federal power steering pump with powder coated bracket and CVF pully for small block. $75.00 + shipping or best offer.

Conversion mounts from 273 to 340/360 in early A body. New, never been used! $100.00 + $20.00 shipping.

Solid lifter rockers etc. from '65 273 Dodge Dart. Springs are missing. $50.00 + shipping via USPS.

I'm cleaning out my garage, and have some parts I don't recognize, but believe the three on the left are from my old 904. The two on the right I believe are for an 833 I pulled off a '69 340. Anyone know for sure and if so is anyone interested?

I've tried installing the window glass first, but then can't get the vent assembly to go far enough to the rear (because it hits the side glass) for it to the front opening. Then I've tried installing the vent window assembly, but I cant get the regulator arm into the bracket on the window. The...

I have a 13" wheel and tire I have no use for since I switched to 15" wheels and larger bolt pattern. Please PM me if interested.

Anyone have or know of a source for the throttle cable grommet or "insulator 14-25-17" as it appears to be described in the picture?

Can anybody take pictures of this and tell which way it runs through the firewall. Thanks in advance. Lee moparlee received no responses from his query back in 2006, so 12 years later I'm asking again... I'm converting my 65 Dart from auto to 4speed and don't know...

Attached is a photo of my 65 Dart Charger waiting for the tow truck to bring her home. Will get the firewall pieces installed, then engine, K member and suspension installed and return it to H & M Auto Care to have the fenders and front valance installed.

My '65 Dodge Dart/Coronet Factory Service Manual doesn't cover factory a/c for the Dart. I guess when it went to print factory air wasn't going to be an option. The Coronet system is completely different. Anyway, wondering if the '66 manual covers factory a/c?

Anyone know of a source for at least OEM quality vinyl top material for a '65-'66 Dart GT? My recollection, and it's been a loooong time is that the original vinyl material had a diamond grain. Someone with an original vinyl top please correct or confirm my recollection.

I need a Federal power steering pump pulley for my '69 340.

Anyone know of a source for a tinted back glass for a '65 Dart?

Engine and transmission complete with factory a/c compressor and power steering pump. Not on engine is alternator and brackets as well as aluminum fins on valve covers. Has low compression pistons and 318 intake manifold installed by a previous owner. Engine ran and transmission shifted properly...

I found a company located in Centreville. MI that sells the entire Charger/Commando exhaust system or just the mufflers or resonators very reasonably. Name of the company is Waldron's Exhaust. Link: 1965-67 Barracuda w/273ci 4bbl carb in Aluminized Steel [7760740200] - $580.00 : Waldron Exhaust...

Need good vacuum canister for the heater control valve on my "65 Dodge Dart with factory air.

need a good heater/air cond. vacuum canister to replace the one on the heater water control valve on my '65 Dodge Dart with factory air.

The heater Vacuum Control Canister doesn't work to pull the water valve to "on" on my '65 Dart GT w/factory air. Are they repairable or where might I find a replacement?

Need a post steering pump pulley for a 1969 up Federal pump. I have a 340 with Moroso aluminum water pump. Have bracket and pump with reservoir, just need pulley. Pump shaft is .652 in diameter.

Wanted, 64-65 4 speed hump.

Looking for a steel hump for a '64 or '65 A-Body. Anyone have one for sale or where I might locate one? TIA

Need a 64-65 4 speed steel hump (transmission cover).

Anyone have good results having the front GT spears re-chromed without losing the GT emblem detail? Or know of a repo supplier?

Anybody been able to restore the hood ornament on a 65 Dart? I've tried bending the 3 tabs back with no sucess. Thinking about just cutting them off, restoring and gluing the assembly back together. Any ideas welcomed, including where to find very good used ones .

When the upholsterer was installing new skins on my front seats, the driver's side button (the rectangular piece with chrome surround) tabs broke. Anyone have a white one? ... but I'll take any color since I can dye one white.

When the upholsterer was installing new skins on my front seats, the driver's side button (the rectangular piece with chrome surround) tabs broke. Anyone have a white one? ... but I'll take any color since I can dye one white.

Anyone know if one can install an inside right tail light assembly to the outside left (or vise versa) by drilling holes for the studs? I don't see any other difference in the two chrome surrounds. For the life of me I don't understand why the Chrysler engineers didn't just design two tail...

I've noticed that most of the original parts on my '65 Dodge Dart were stamped with the CPDD logo. I understand why it would still be on parts that were carried over from the early years, but my taillight lens have the logo and I doubt they were being produced in 1962. Anyone know why the...