Search results for query: *

https://m.facebook.com/story.php?story_fbid=pfbid02J3aCiix56YqhRSqPvC7novyp4Yc4XtbxEgXD5AWepn6G36y13eY3YmMup2SUSnsil&id=100050401837799&m_entstream_source=permalink&__tn__=-R thought I would post this for a guy in the town I live in.

Valve body and park rod, came off a 71 904 trans, was swapped for a manual valve body, $25 shipped to lower 48 states from SE MN.

moroso part number 64930 1 inch 4 hole carb spacer. $20 shipped to lower 48 states from SE MN.

4 blade fan with spacer and original bolts, $25 shipped to lower 48 states from SE MN.

Came off a 73 727/318 combo, nice shape just needs to be cleaned up. $50 shipped to lower 48 states from SE MN.

I have 2 valve bodies for sale, one came out of a 1970 904 trans, the other from a 1973 727 trans, this one has a shift kit of some kind in it. Both pulled out for manual valve bodies. $40 shipped in the lower 48 for the pair.

I have a used 741 case with a 294 ring and pinion, small yoke, has caps, ring gear bolts also. The sure grip was taken out of it but will include an open center if buyer wants it. $175 shipped in lower 48 states from Spring Valley, MN, 55975.

Took this out of my 68 340 GTS with 727 trans. Was used until I switched to an aftermarket shifter. $125 shipped from 55975 to lower 48 states.

Came off my 68 dart gts with 340, was used until I put a manual valve body in. I have the bell crank also, need to get if off the intake. $175 shipped to lower 48. shipping from 55975, southern MN.

I pulled this out of a 71 904 to install manual valve body few years ago, been sitting since. $35 plus shipping from 55975, should fit in a large flat rate box.

Brand new in the box, high vibration blaster2 coil, new they are around $60, this one $45 shipped in lower 48 states from 55975.

I have 9 u joints still in boxes, bought at an auction few years ago and never used them. I searched some of the part numbers, some ram 3500 and some jeep. $75 shipped in lower 48 states from 55975.

Used Mopar Performance MSD Box with 7k chip. new blaster coil, Box was bench tested, works good. Coil is new never used. $165 plus shipping from 55975.

SOLD Carb 9103 S, was taken apart and checked, all parts look to be there, linkage is free. Carb came on a motor I bought, never tried using it. All linkage is off as well as top just sitting on base. Good for rebuild or parts. $45 shipped to lower 48 from 55975. SOLD

Small block 10.5 inch flywheel, neutral balance, came off a 71 340, will most likely need a resurface done, $65 plus shipping from 55975.

Took this out of a A833 aluminum od trans with 10.5 inch clutch, $30 plus the ride from 55975. Doesn't include Z bar in pic.

Set of 4.56 gears, less than 500 miles on new set of Richmond gears, 30 spline, 742 case large yoke, nice and quiet, $550 plus shipping from 55975. shipping is usually $60-$75 depending on location. pics taken just before install

Comes with bolt, cast iron $75 plus shipping from 55975.

VIN # 1B177944, came in a parts car I bought.

Got this set in a parts car, cone sure grip pin is not broken or egged out in case, turns freely, gear look good, $300 plus shipping or buyer picks up from Spring Valley MN 55975

Got this trans in a parts car, goes into gear and turn freely, was full of fluid when I pulled it out. The tail shaft is cast iron and the longer one with 2 shifter mounts, 23 spline, Located in Spring Valley MN 55975, $250 buyer pays shipping or picks up.

Thought I would share some pics of the parts car 73 340 4 speed charger with a 71 340 I bought last month at an auction. Not an A body but I bought it just for the 340 and I finally pulled the motor out last week, car was stored inside and the engine still has coolant so hopefully all is good...

Good shape, could use a repaint, $125 plus shipping from SE MN, 55975

Made it to the track with new MP 557/296 solid cam in my 340, advanced 4 degrees when I degreed it in, stock replacement pistons, X heads with some bowl clean up. Last summer at the track with the old cam, MP 508/280 solid, 4.10 rear gear and 27 inch tires, it ran 13.40's @ 102 with full...

Used clutch fork, came out of a 70 340 duster. $45 shipped to lower 48. Located in SE MN.

Looking for an early cast iron small block water pump pulley for a/c, 67-69 I believe. Should be 5 3/4 in diameter, non a/c is 6 1/2 in.

Just a question about the up and down play of the pitman arm shaft on my 68 dart with factory manual steering. If I adjust the jam nut and screw at the top of the steering box, will it take the up and down play out of it? I replaced the idler arm and noticed the pitman arm shaft has some play...

I have my small block factory X heads apart to set up springs, clean up the bowl area and check them over. Looking at replacing the intake valves, a couple are a little beat up around the lock. My question is what valve has anyone used as a replacement? I have the old TRW V2811X in it now...

I have a set of lower dash pads for 68 dart/barracuda, these are blue but can be dyed to match, very nice shape, no cracks that I can see, located in SE Minnesota 55975, $125 shipped to lower 48.

I have a 4 blade fixed fan with spacer for small block mopar, located in SE Minnesota, 55975, $25 plus shipping