Search results for query: *

  1. 66plyValiant

    Old school 5.7

    not to drag up old threads but what did your buddy use for plug wires? they look of the napa belden brand
  2. 66plyValiant

    [WANTED] Air cleaner assembly from a Dakota

    the setup you posted is not from a pre 1996 dakota, its from a 1996+ dakota or ram/ram van, I think I have one if your interested but I'm in canada
  3. 66plyValiant

    1964 DODGE DART SLANT 6 to a V8

    my car runs a 904 automatic, 1993 dodge dakota v8 manifold (other years work just fine) the part where it bolts onto the head is plained down quite abit, 1/4" comes to mind but I forget, 2 washer shims under biscuit engine mount on drivers side and nothing hits with factory power steering
  4. 66plyValiant

    318 draw through build

    from what I know about draw through turbo's 1) reed valves are to allow air/fuel mixture a quicker route to intake 2) as number 1 says if you mount the carb elsewhere you would have to pump the crap out of the car to get it to start, ever started a crossram car when it hasen't been running...
  5. 66plyValiant

    opinions thoughts ideas

    no sense it building an engine you don't really want to end up with though, open the 360 up, check bearings, rings and the important stuff have the heads checked and button it back up and run it like that if all looks well
  6. 66plyValiant

    opinions thoughts ideas

    is the 360 a good running engine? did you hear it run? if so drop it in and run it, buy the 340 and save it until you have abit more of a budget to build it (sit in in the corner) that way you have the 340 to build and still can drive the car with the 360
  7. 66plyValiant

    Hellcat Engine Swap

    if you have new vehicle replacement its an automatic write off after a certain cost to fix; every insurance company offers this coverage and its almost stupid not to have it, this car was wrote off because of that I'm sure as its not even hit that hard
  8. 66plyValiant

    Hellcat Engine Swap

    insurance don't repair brand new cars if you have the proper coverage; new vehicle replacement, would you want your brand new smashed car back or a brand new one like it? that car is quite fixable but your correct that most insurance companies total the car because the air bags cost more then...
  9. 66plyValiant

    63/67 valiant ( not mine )

    a person who invests 30K on a car doesn't just shove the clutch pedal to the floor and leave it there as a decoration, they would also clean and paint the trunk body color, and the wiring wouldn't have wire joiners on it $7000 would have been more real of a price
  10. 66plyValiant

    63/67 valiant ( not mine )

    it sold for $7000 in the auction link, far below the 19,000 he was asking on craigslist
  11. 66plyValiant

    63/67 valiant ( not mine )

    its not an error, he replyed to a member here saying the car was a 1965 titled as a 1967, its illegal to sell something like that
  12. 66plyValiant

    63/67 valiant ( not mine )

    because this guy is selling something that isn't legal, a 1967 title for a 1963-65 car that is a mix matched parts
  13. 66plyValiant

    63/67 valiant ( not mine )

    not a 67 they stopped putting torsion bar hood springs on in 1966, looks like he is trying to flip the car for major profit; I know some beautiful looking cars for $20K
  14. 66plyValiant

    Throttle doesn't open all the way fix

    why not just bend the top of the pedal assembly a little outward to allow the pedal to pull the cable further out of the firewall before it hits the stop
  15. 66plyValiant

    How too Narrow a gas tank!

    thats a really horrible spot for a fuel tank, right in line with the passenger side rear tire; most people put in a fuel cell because the engine isn't stock, meaning your probably going to be spinning it and have about 80 percent better chance of having a tire shread the wheel wheel
  16. 66plyValiant

    Budget EFI Kit

    sorry to those that have responed and I haven't got back to you, yes I still do the v8 kits, usually 2 per year can do more if there is a demand haven't had major amounts of time, now have a little one and a new to me house. slant kit works but haven't spent any more time on it to get it to...
  17. 66plyValiant

    hydroboost brakes

    this change over was done for a couple reasons. quicker stopping power and easier pedal effort, this was done so my father who is disabled could enjoy the car too without as much effort to push the brake
  18. 66plyValiant

    Electric Fuel Pump Just Quit?

    95 GPH? what are you running a double street hemi set up?:D 7 PSI is getting up there for a single 4 barrel but will work fine for the most part, more fuel then most engines need
  19. 66plyValiant

    318 draw through build

    if you buy used turbos make sure there not from a diesel application, apparently they dont have the proper seals in them for oil
  20. 66plyValiant

    spindle interchangability questions

    yupp it will fit, but you've now opened the can of worms from the people who believe it will understeer because there "different"
  21. 66plyValiant

    Crank Sensor

    if your running a TBI engine, 1988-1991 LA series then it does not use a crank sensor, it uses a special distributor that has a hall effect sensor much like the one that the magnum uses except it mounts different TBI won't run off a stock electronic ignition in mopar, unless you use all chebby...
  22. 66plyValiant

    Pedal goes to floor

    if you have a 1980 dodge nobody bothers with backyard rebuilding anymore, there under $60 each for calipers and a normally stocked item if you drained the master cylinder and pumped the pedal you will have fun now, the master will need to be "bench bled" (done on vehicle) then the proportioning...
  23. 66plyValiant

    What engine did I just find?

    okay, sometimes detectives cars only got a 318-2 or sometimes city police only got a /6 engine, there is no rhythm nor reason why anything was done at that point in time
  24. 66plyValiant

    66 Sport Fury Grille **Nicest you will find**

    if he does it would amaze me, this thread is 4 years old!:wack:
  25. 66plyValiant

    What engine did I just find?

    360 heads and intake on the 318, all AHB M bodies were built like that unless it was a detectives car
  26. 66plyValiant

    What engine did I just find?

    looks like your normal 318 4 barrel truck engine for 1981
  27. 66plyValiant

    Single cylinder glaze honing?

    1/2 a quart every 8K is actually considered normal oil usage by most car companies
  28. 66plyValiant

    Intake manifold won't seal - How do I check it ?

    if the heads or block has been machined the intake will need to be to fit the different angle that is now there
  29. 66plyValiant

    Question to all the welders out there!!!

    its great for starting to weld but you will soon find you don't like it, doesn't weld nearly as good as a gas welder and has way more splatter then one, however you can use a flux welder anywhere outside; gas you can't
  30. 66plyValiant

    My Power Disk Brakes are frustrating me...

    with the timing you may need an adjustable light to be able to see where your sitting at idle, could be that its flashing around 16+ which is hard for a normal light to pick up on
Back
Top