Search results for query: *

I have just started a 5.7 hemi swap into a '68 2wd Suburban (partially for the power, partially to piss off the Chevy guys). I have a complete 2005 half ton Dodge pickup donor. I plan to use the complete motor/trans (auto), along with the stock gauges from the Dodge. I know there are a lot of...

I am getting to order a flywheel for my slightly modified 360 Magnum that will be going in my Demon. Looks like the choices are the Mopar P5249842 and the Mcleod 464102-15A. The main difference I see is the MP flywheel weighs 18.5 lbs and the Mcleod 30 lbs. Any suggestions? Car will have some...

Does anyone know the difference between the Mopar P4529110 (360 LA) and P5249842 (360 Magnum) flywheels? Both are 130 tooth, 10.5" clutch, 6 bolt attachment to crank. Any thoughts?

I have a Dart/Demon dual snorkel hood scoop, I am missing the lower front part of the snorkels. Please message me if you have one or might know where one is. Thanks!

Looking at getting a new set of headers for my small block 4 speed Demon. Do all brands require that the steering be disassembled to install the drivers side header? The headers that came with the car are this way. Thanks in advance!

I found a new in the crate 360 Magnum engine and I am thinking of putting it in my 4 speed Demon. I did a little research on what needs to be done to install it in place of a standard small block. Are there and cheap mods that can be made to it to bump up the performance? Was told that shaving...

I'm putting together a street/strip '71 Demon, will be running a slightly warmed over 318 and a 4 speed. Approx. 26" tall drag radials, 8 3/4 posi. Should I run with 3:55 or 3:91 gears? Thanks in advance!

After driving my Valiant wagon home the other night, I found it was leaking fuel from the sending unit in the front of the gas tank. I pulled it apart and found the sending unit gasket had seen its last day of usefullness. After an unsuccessful trip to the Oreilly's down the street for some...

Looking for a '70-'71 Dodge Dart / Swinger grill or '71 Demon grill, need headlight surrounds also. Thanks!

Just a warning, do not conduct business with Rob at Midwest Performance Products in Diller Nebraska. He sells questionable quality parts, does not stand behind his work or the parts he sells. The Pro Comp CNC castings are pretty nice, the valves, springs etc. he installed are JUNK! The springs...

Crane big block roller rockers, 1.5 ratio with shafts, fit standard big block heads. Good condition, they sell for $531.00 at Summit, $250.00 including shipping in the lower 48 states.

Selling a new, never installed full set of 5 red seat belts. These came with a 1964 Plymouth Valiant station wagon that I am now parting out. They look just like the originals, but have a slightly different buckle system. Three are 60" long and the other two are 74" long. I have the receipt...

2 (high/low) horns from a 64 Valiant wagon. They work fine. Also have 6 cyl. motor/trans, push button shifter etc.

Parting out my 1964 Valiant wagon. Complete tail gate, doors, bumpers, some glass, also have interior and mechanical parts. Let me know what you need. Thanks!

1964 Valiant 200 station wagon for parts. 6 cyl. push button auto. Have dash parts, motor/trans, some body, glass and trim. No grill or front valance. Head light rings are rough but may be able to be fixed. Let me know what you are looking for. Car is located in Boise Idaho.

Will a later A-body 8 3/4 fit in a '65 A-body with no major modifications?

Has anyone run the Procomp aluminum big block heads? The CNC ported ones look to have pretty decent flow numbers.

I am looking for a gas cap for my 1965 Plymouth Valiant wagon. The local parts stores do not list them any longer. Any thoughts?

I have a 1971 Demon Sizzler. It is a roller, no motor or transmission (was a 318/auto), and is a full project. It has minimal rust (has a spot under the battery). The car is very straight, all glass is good as well as the grill and tail lights. It was B5 blue from the factory (have not seen any...

Just got done installing exhaust manifolds from a 1992 Dakota into my 1965 Valiant wagon. I did have to do a little "massaging" on the drivers side manifold (as seen in the first picture). I did install the manifolds after the motor was installed, you will need to use bolts only (no studs) to...

I posted this question in the small block tech area, probably should have posted it here in the first place. Will the early (pre-67) and late (67-later) model a-body small block oil pans interchange chassis wise? I'm planning on putting an early 70's 318 in my 65 Valiant wagon this winter...

Will the early and late model a-body small block oil pans interchange? I'm planning on putting an early 70's 318 in my 65 Valiant wagon this winter. Thanks!

I am trying to identify a cam I pulled out of a small block. The only numbers I can find are 930503 on the dist. gear end of the cam (see photo) other than some casting numbers in between some of the journals. There is a little purple paint sprayed on the cam. Any thoughts as to what this is?

I am looking for a back up light lens for a 65 Valiant station wagon. Any leads are appreciated!

Hello all, I'm new to the site. I picked up a '71 Demon Sizzler earlier this year. The car is B5 blue w/white stripes, 318/auto, full project but very straight. Motor and trans are gone. Does anyone have somewhat accurate production numbers for these? I've seen a full range of production...