Search results for query: *

I have a really nice original A body 8 3/4 rear end. I have had this one for years but I don't see myself using it anytime soon so time to send it down the road. This is an original housing not a narrowed one. Still has original paint and the original paint stencil markings on it. It has the...

I haven't pre-registered. Just pay at the gate probably... Not sure what cars I am going to bring yet, so don't want to sign up for the wrong classes...

I have a ton of parts to sell, but I am bring 2 of my cars to put in the show... Just have to decide which 2 to bring! Haha Glad the show is finally coming back.

Yucaipa

I sold the complete one for $1,250 but I still have the other 2 avaliable.

10/2/67 Standard bore. These early blocks don't have pads for vin. numbers. 9/23/70 Standard bore. partial vin stamped 1B32493. The 7/1/70 engine and the 5/29/73 engine don't have vins stamped. I don't have the vin off of the '69 block with me but I will try to get it and post it up.

What would you guys think a set of hubs and rotors are worth?

Thanks but I am looking to see if new ones are available or not.

I am wondering if small bolt pattern rotor are available anywhere? Also, are small bolt pattern hubs and rotors available anywhere? Thank you, Jeff

I have a 904 trans I got from my buddy a while back. He said it came out of his '70 Challenger that was a driving car. $100 located in Southern California Thank you, Jeff

I have been hoarding parts for a long time and I am going a different direction now so it's time to thin the heard. I have 5 340 engines for sale. I will drop them off at a Fastenal if you would like them shipped. #1.) 1967 cast block. Standard bore. No visual damage. $2,500 #2.) 1969 cast...

I have 3 different A-Body 8 3/4 rear ends. I have been hoarding some parts for years and decided to go in a different direction so it's time to sell them all. #1.) A-Body 8 3/4 housing. Cleaned up and painted with new axle seals installed. Has new big bolt pattern axles with green bearings...

Yeah that's why I'm hitting the forum to see if someone on here has one or two of them to help another Mopar guy out for a reasonable cost!

Looking for a Claude Short Dodge License plate frame. It was the dealer where my T/A was sold new in Santa Monica California. Any help would be greatly appreciated! Jeff

I will try to get a pic of that and upload it before I leave on vacation.

True. The single 4 barrel top plate is filled in underneath and will work on my intake. It will just have that extra bolt not used.

Original Mopar Dana 60. 60" wheel mounting width (68-70 B body) 4.56 gears clutch posi 11x2-1/2" brakes, no drums. Asking $2,000 located in Southern California. Thanks for looking! Jeff

I have an Edelbrock STR 14 intake with 2 different top plates. Cross ram and single 4 barrel. Also have 2 new gaskets for top plate to intake. The cross ram top plate had 2 cracks out in the open(probably from a backfire) that was professionally repaired from the bottom and from the top you...

I have quite a few transmissions and I will never use them all so up for sale listed below. Big block 727. 1966 and up. For car. Good used. $450 Big block 727. 1962-1964. For car. Rebuilt by Art Carr. Good used. $300 Big Block 727. 1965. 1 year only cable shift and slip yoke. Good used...

I have an a original a body 8 3/4 rear end with small bolt pattern. Axles, Brakes and original bell brake drums. $1,000 no 3rd member 742 case 3.23 open third member. $250 Located in Southern California. Thanks for looking! Jeff

I have an original '73 340 727 automatic transmission for sale. Good used condition. $400 Located in Southern California. Thanks for looking! Jeff

I have several 340 blocks for sale, if you buy a block I will offer you a crank, rods, heads, intake, etc. for extra $. '67 block standard bore. Date 10/2/67. $1,500 '68 block fresh .020. Date 9/11/68. Vin. # LS23P9E133254 $1,300 '69 block. .020. Date 8/11/69. No Vin. # stamped (warranty block)...

I am wondering if anyone has cut a convertible in half and has also cut a hardtop or 4 door or sedan in half and notced what is in the rockers. I would assume that a convertible would have more metal in the rockers since the car isn't trussed by the roof, but I am curious to see if it actually...