Search results for query: *

I finally got them up loaded Bob

I haven't been able to post pictures. I have my nephew try to down load. Bob

i post pict tomorrow

They are for the street rod application with early ford flat head dount rubber mount i will post pict.

I need truck ram horm style flange to pipe gaskets. 4 of them if anyone has them or where I can gat them Bob

I have the water pump housing timing civer chrome, (used) Oilpan with pickup tube for an A body and petronic distributor. All for Big block and Hurst baby Hemi motor mounts

I CAN SEND TOMORROW CALL ANYTIME Phone # deleted by STAFF. Please read the rules. BOB

2.2

New Drivers side outlet aluminum water pump housing $50 + shipping New Chrome Alt Mount Bracket $20 + shipping Chrome (used) timing cover $15 + shipping

Have a set of Hurst early Hemi mounts $75 plus shipping Bob

For Sale Complete Rebuilt 1996 Chrysler turbo engine with good transmission rebuilt half shafts. Mounts, compressor, starter, alternator, all vacuum lines, computer, wire harness, correct map sensor and waste gate (Both New) for 14 lb. boost, Engine is still in car come hear it run and drive it...

Can you contact me through this site? I responded and I think it was deleted because I had my phone number abd email in it. Thanks Bob

I have a speed gem mopar to chevy. flywheel, block plate and starters. early & late model Will fit t10 Muncie IROC World class and Ford T 86. Should fit 331 Also have baby hemi motor mounts $50. $450 + shipping $750 with IROC T5 More pictures [Email address deleted by STAFF] Has to be shipped in...

I need the peddles, shifter w cabled, trans, flywheel, pressure plate, bearings. I would prefer the complete car. I would like the disk brakes aslo and any other options it may have Tili wheel and cruise controll and tilt wheel.I can pick it up and dispose of the shell, Don't need papers. Lets...

Wanted rotted, wrecked, rollover burned not running is ok ,Dodge, Plymouth, Sundance, Shadow or 400 or any mid 80"s K car with five speed. Will pick up and/or pay reasonable price. I want to swap out an automatic to manual 5 speed transmissions in my car. Also will swap for same in a good car if...

I had a similar problem with my street rod. The bolt (with lock tight) backed out. I found that this caused the spindle to bend slightly. I had to drill the head of the bolts and wire them. Hope you get it fixed. Bob

Motor Home 727 without the e/brake drum on the tail shaft are about the length of a short shaft Turbo 400. I had this in my 65 dart. Much shorter then the original and long 727.

I have a Speed Gem bell housing for BB Mopar with starters and flywheel to install GM trans with or without IROC T5

Looking for original, repo or good used set of Long Tube (Soni Ram) air cleaners. Please send pictures with price. (See my avatar for application needed) Bob

Use a drag link socket they come in different sizes. Hope this helps. Bob

I HAVE A SPEED GEM MOPAR BELLHOUSING (SG-13-T) ADAPTOR. IT'S DRILLED FOR FORD AND CHEVY BOLT PATTERN TRANSMISSION I HAVE A FORD IROC STYLE T5 ON IT. THERE IS ROOM ON THE BELL TO DRILL OUT FOR OTHER TRANMISSIONS ALSO HAVE THE BLOCK PLATE CORRECT 12VOLT STARTER, FLYWHEEL, CLUTCH DISC. PIOLET...

TIRES FOR SALE All are new 2 175/70 x 13 $ 50.00 5 225/60 x 16 $ 150.00 5 225/60 x 16 $ 150.00 Can email Picts.

I have one in my 32 Roadster w/ 440 and 65 Dart Gt 340. also use the crab and original type in my 32 coupe with a flat head. No problems with all 4 electronic, all from speed way. Bob

They need spacers to clear some heads. I have them on my 440. I changed to aluminum heads and don't need the spacers. The spacers also block off the heat riser in the original head. There for sale

Are they the ones in the picture and are they still avaiable, what are you asking. That my 65 Datr GT 440 Soni Ram want aset for s 32 roadster Bob

I have s Speed Gem conversion for Mopar to IROC T5. Bell housing, flywheel, starter, Block plate. I don't have any linkage parts I was using a hydraulic throwout bearing. $400 & shipping Bob

NOS SPEED GEMS PART # SG-13-T I AM SWAPING TO A/T Mopar Big Block to GM 4 speed Bellhousing 1956/1961 With New 143 tooth flywheel (drilled for 10 & 11 inch clutch) Rebuilt starter Have instruction sheet $500 complete Plus shipping I have a rebuildable T5 Core @$100 AS YOU CAN SEE IT ON A 440 R...

SPEED GEMS PART # SG-13-T NOS I AM SWAPING TO A/T Mopar Big Block to GM 4 speed Bellhousing 1956/1961 With New 143 tooth flywheel (drilled for 10" & 11" clutch Rebuilt starter Have instruction sheet $500 complete Plus shipping I have a rebuildable T5 Core @$100 AS YOU CAN SEE IT ON...

2012 Black with Polished Diamond plate trim 14 X 7 V- nose enclosed cargo trailer. Rear ramp and side door. Interior lights. has buddy bearing on all wheels I bought it new In Georgia drove it to NJ moved my daughter and tools to Wisconsin. Has about 3000 miles on it. Will deliver to Midwest...

Pishta, Sorry if I came off sounding that way. I didn't understand what the letters were and what the obvious faults of the covair had to do withthe boxes use in other applications. I have used them in 32's, T's, fat fender's as well as other cars. There repops now sold for the same reasons...