Search results for query: *

Hi guys. I a rebuilding a 1972 Dart. I have an AC car but no AC components. I am looking for everything: Under hood Heater/AC box Dash controls Prefer to buy an entire set up, but let me know what you have. Thanks, Pete

Guys, I wanted to pose a question and get your feedback as you are the most knowledgeable Mopar guys around. Here is my story: I have 2 Mopar A-bodies - a 1972 Dart Swinger that is in pieces - Stripped down to the shell. Over the past several years, I have been rebuilding components in my...

i am going to swap my 318 for a 340 in my 72 Dart. I don't believe that I have ever seen a 340 with air. I don't think it should be a problem, but I thought I would run it by you guys to make sure. Don't judge me, I just like AC! Pete

I have a 72 swinger shell that I am gathering parts for. It is an AC car and I want to rebuild it that way. Unfortunately, no AC parts. What model years can I use for parts? Can I use my 74 Duster for reference? I seem to remember that there was a change in systems and set ups at some point.

I have a 1974 Duster with a 318 / 904 set up. I am considering swapping my 1971 340 into the vehicle, but I want to make sure that I have all my bases covered. What engine mounts do I need to use? The 340 will mate to the 904 with no problems, right? All of the current 318 underhood...

You are looking at a really cool 1974 25,000 original mile 318 Plymouth Duster. I hate to sell it, but other priorities have crept up...... This car is extremely original - A True Time Capsule. It could use a little TLC, or drive it as is - ORIGINAL. The car has two build sheets and tons...

Following is a list of parts that I have been accumulating and preparing to assemble a 1972 Dart Swinger. Photos and more detail on the condition of each item is available, PM me. It is all really good, however. I will do an actual inventory this weekend and update this list. If you do...

Hello all, I am rebuilding my 3-speed that came with the car. Can't seem to find a good supplier of rebuild kits (seals, bearings, gaskets, gears, synchronizers, etc.) for this model. Anybody have any recommendations? Thanks, Pete

Guys, Is there a difference between pre-1973 upper control arms disc vs. drum? They look the same to me. Thanks for the help.

Is there a difference between heater / ac boxes between 1972 & 1973 A bodies (Dart specifically). Several 1973 on ebay. Can't I use any box from 1970-76?

I am looking for the entire heater/ac system for my 1972 dart. Controls, box, vents, and under hood stuff too. Let me know what you have! Pete

Hello, I am rebuilding a 1972 Dart. I will use a 340 with a 230 3 speed transmission. The car will also have a 8.75 742 Rearend. I am going to have a propeller shaft built, and I wanted to run my plans by you gys to make sure I am going in the right direction: What I believe is that the...

1. How can I confirm that the K-Member that I have is correct for a V8? (Car had no engine when I got it) 2. How can I confirm if my steering gear is power or not? Part Number? 3. If my steering gear is manual, and I want to take the car to power steering, will I need a new Steering...

Cleaning out the garage. I have some original 70 Swinger Rear seat bench and Back covers. in good shape for a driver. I also have new front bench cushion cover and seat back covers. Front cushion was cut when my wife drove over it in the driveway (long story, but a funny one). I believe that...

I just replaced my underdash harness. The old one was "customized" and I had a short somewhere that melted the ignition wire. New harness and ignition swich are in and the car fires right up. Two issues: 1. The old ignition switch had an orange wire that ran to to gear selector light on...

I am looking for one door jamb switch for my 70 Dart. Looked around and I see that I am not the first person to have this issue. I bought a couple new ones and the threads are too small. I believe the threads are 1/2" course and I used a 9/16" wrench to remove it. It has two terminals...

OK Guys, I need some help! I had an electrical problem where the fusible link on the ignition blew. It melted the large red wire on both sides of the underdash connector. I am trying to remove the harness from the steering column, and I am stuck. It is a Slant 6 904 automatic. I have the...

Does anyone have a working oil pressure gauge that they are willing to sell? Could use one for my 70 340 Swinger. Pete

Rebuilt my Rallye Dash and got every gauge working but the Oil Pressure Gauge. 340 Car. The way I figure it, either the sending unit, wiring, voltage limiter, gauge, or some combination of these are bad. I checked the gauge with an Ohm meter before installing it and it was good. Figured...

Looking to sell my 340 Dart. Original 340 EK2 - Go Mango 4 speed 2 partial Build Sheets confirm the originality of this car Professionally Rebuilt Date Coded 340 - Original Engine Gone Professionally Rebuilt 833 4 Speed Transmission New Interior Rebuilt Instrument Panel No Rust - New floor...

Guys, Can someone give me some background on why there were 3 different 3rd members offered on the 8.75" axle? What are the differences between each one, and what were the determining factors that put them into different vehicles? Long term, I will swap out my Slant 6 with a 340. I will...

Looking for an axle to handle the V8 swap. 3.23 or 3.55 preferred. Anyone with anything that they are looking to get rid of?

I have a rusty 13" wheel in the trunk of my 1970 Dart that was there when I bought it. Was the original spare tire a 13" or 14" wheel? What was the correct spare tire size? Car has 14" wheels. Thanks

I am thinking about adding power steering to my 1970 Slant 6. I know that I need to add the following: Power Steering Pump & Bracket Power Steering Gear (Box) Power Steering Column (with coupler)- Automatic Trans. 1. Am I missing something? 2. Are these parts different between a /6 and a...

Thinking about replacing my /6 with a V8 and I figured, what the heck, might as well go with a 440. I know many of you have experience here so I figured I would get your thoughts on what to look out for before I get going. I am thinking about keeping it more stock probably with a 727...

Is the 340 k frame different than the 225 slant 6? If I swap the 340 for the 225, do I need to change it? Thanks for the help

Does anyone have one that they would care to sell me? Screwed mine up trying to get the bushing out. Thanks for the help. Pete

Guys, What is the best way to remove the upper ball joint? Pete

Anyone have any idea where I can find some 340 exhaust manifolds? Any help would be appreciated. Pete

So, Finally getting the dart back together and I went to install the thumbwheel radio that I picked up on eBay, and it doesn't fit in the rallye dash bezel. Turns out it is from a 68 b-body (I believe). Looks like I can change the bezel on the radio and I believe that it should fit. Am I...