Search results for query: *

Having what it seems to be a distributor problem, car is hesitating and bucking while driving. Looking to see if anyone has a stock /6 distributor laying around. Local to PA w o uld be the best. TIA

Looking for a 225 Slant....would be interested in motor and trans combo or just the motor. Located in PA, so i would like it close so i could pickup. Let me know what you got! Thank You

I have finally decided to put the vinyl top on my car, when I purchased the car the previous owner had put almost like a spray on bedliner like material on the roof. To make the vinyl top adhere correctly would you advise just to sand it down or to strip it all off?? Thanks

72 Dart /6 Car will randomly start to over charge and peg the volt meter, when this happens the engine will start missing and the car will barely move.......any ideas on what is going wrong?

Revers Light Wiring Diagram..... Anyone have a diagram or know where I can get one for a 72 Dart Swinger? Automatic 904-/6 Thanks!

What is the correct color for the headlight buckets and the adjuster plates for a 72 dart? Thanks!

Dart hood trim off a '72 Swinger has a little dent in one spot, but not in to bad of condition. $50 Shipped to upper 48

Need a SBP Rear End for a 72 Dart...looking for something a little more aggressive then the 2:71:1 I have currently. Sure grip would be a plus. I'm in Shermans Dale, Pennsylvania, so I would prefer something under an 8 hour drive. Thanks! :D

I've tried looking everywhere for this before I posted..... On line 5 of the broadcast sheet I would like to know what these codes are: All are under the brown header "Wheels" Road-45 Color-TX9-(Black?) Spare-00 Then beside it: Wheel Cover-60 I know from the T12 code it was a 6.95*14 WSW...

Front Bench Seat w/ everything shown-$150 OBO Rear Seat-$50.00 OBO Dome Light w/ wiring-$20 OBO Seats are for pickup only, dome light I will ship...... Wanna sell it, send me an offer!!

Dart Parts-Rear Quarter Extensions$30/pair License Plate Frames-$10 Each/ I have 2 looks brand new!-SOLD Hood-$100 Fenders-$50 Each Lower Quarter Patch Panels-$20 Each -SOLD-Someone local came to pick up other parts while I was not home and these are gone too! All prices OBO...... LOCAL PICKUP...

Looking for SBP steel wheels for a 72 dart, im wanting to run dig dishes on my car. Looking for a complete set of 4 rims. Thanks!

I've heard some pretty descent sounding cars on youtube, but nothing in person. What is your favorite exhaust/muffler for a /6?? I barely can hear my car run right now, looking to do something a little different.

Who still has hood insulation on their vehicle? and if so do you have any pictures you can post of it. Trying to decide if I want to put it on or not.

Looking for all 3 pcs of the trunk trim for a 72 Dart Swinger. Mine are pretty good just one is dented pretty good. Thanks!

$250 Shipped *These were original steel, not coated...never been put on a car, they had surface rust on them......I cleaned them up and painted them high temp silver header paint. The DD2 header set is designed to fit big block Chrysler (383-440) V8 engines in 1932-Up cars and pickup...

What heads would be the better choice for me?? Casting Numbers: 2406516 3462346 This is for a 383 stock type rebuild, edelb 4b intake, factory/small cam nothing crazy. exhaust I have factory a body big block manifolds. Short Deck Block 727 Trans/Gearing undecided yet.

1994 Dodge 360 Magnum Enigne, vin code "Z" came out of running 3/4 ton van comes with everything but intake Rockers where backed off so no valves would stick and intake ports were taped shut. $300 OBO Local pickup only, will not ship :banghead:

Looking for a Big Block combo for a 72 Dart. I Have most of the parts needed to swap already for a 383 but may consider a 440. Needing the BIG STUFF THOUGH: Engine Trans Rear Drive Shaft Must be within descent driving distance of Pennsylvania. PM me with prices and what ya got. Thanks!:blob:

This has been a problem since i got this car......the carb was bad so i just replaced that.....now the car will idle fine, free rev fine, and will drive fine, BUT it has no power at all....you can floor it and the car wont pull past 2800-3000 rpm.....I have checked the timing and it was on, the...

Just a general question when building a 383, what have you found out to produce the most low end torque and descent power.....not reving the car to the moon. Trying to get some opinions before i start a build. Thanks

BEING RELISTED DUE TO NO SALE 1994 Dodge 360 Magnum Enigne, vin code "Z" came out of running 3/4 ton van comes with everything but intake Rockers where backed off so no valves would stick and intake ports were taped shut. $350 OBO Ceramic Coated LT Headers i got with this engine when i...

This was first an occasional problem, now the car wont move......As soon as you put the car in gear and give it any throttle it will stall out like its tight. The car will idle fine sitting and you can put it in gear with your fott on the brake, but it seems to load the enigne so hard and stall...

1994 Dodge 360 Magnum Enigne, vin code "Z" came out of running 3/4 ton van comes with everything but intake Rockers where backed off so no valves would stick and intake ports were taped shut. $500 OBO Ceramic Coated LT Headers i got with this engine when i purchased this car, dont know what...

Does anyone have a picture of the correct front seat for a 72 swinger? And im new to the mopar game, where all vinyl top cars actually vinyl tops or where some painted?? (Not to sound stupid):? Thanks for the help!

These are some mirrors i have left, will make a package deal if someone wants them all. Pm if interested and make me an offer.

This is hood trim off my 72 Dart Swinger, its just the hood piece itself. In pretty good hape, just has a couple small dinks in it. Make me an offer on it!

I have two radios-Chrysler Solid State Radios. One is a little larger than the other. One has chrome buttons and one has black ones. I DO NOT KNOW what they came out of or if they even work. With a little bit of clean up they should clean up nice. $25 Each+shipping

This is my 72 Dart Swinger i have been working on, right now its a /6 car. Thinking about converting to a V8 but still not sure yet. Car cleaned up very well, have a lot of time in detailing it all over and trying to make it look as best as possible for now. Hopefully this winner its going to...

72 Swinger front seat needed.....prefer black. Thought i found one and it did not happen. Any help would be greatly appreciated.