Search results for query: *

looking for a MOPAR PERFORMANCE aluminum intake manifold for an LA engine (273,318,340,360) single plane with the LA MOUNTING holes not magnum engine mounting. If you have one you would like to sell pm me and please send pictures thank you

I’m listing a 1963 dodge dart 4 door for sale it has the 170 c.i. slant 6 with a 3 speed manual trans mission column shifted. The dart was last driven 6 years ago, ran and shifted good. The car has decent fenders & hood. Trunk lid has a wrinkle but not super bad, I didn’t notice any major rust...

Reconditioned altenator 75 amp output single groove v-belt pulley. This has not been installed since being rebuilt its been sitting on the shelf way to long so its time to sell. I did take to local rebuilder to verify output and that it still worked. Located in west michigan. $75.00 plus shipping.

From a 1976 duster, so it has the key in the colmun with key release button a steering column with keys both door and trunk cylinders the keys work all lock cylinders, and a bottom cover in black. The column has a power steerin connector and firewall penetration cover. The only negative that i...

looking for a nice pair of 7” stainless headlight retainer trim ring. Please pm me if you have a pair you want to get rid of. Tom

Cleaning out the garage of things i am not going to use, if someone has use for or wants to take time to sell all you haveto do is pay for shipping or come and pick it up, i am located in grand rapids mich.If no one wants this by September 11 its going in the trash. It came from a 76 duster 2...

I am looking for a pivot shaft for a ply./dodge duster or dart 70 to 76 needs to be smooth operating.

wiring harness from a 76 duster decent condition considering its going on 40+ years old. It has the bulkhead fitting and the under dash connections and swtches, all connectors are in nice condition there is 2 wires that have been cut don’t know what they went to. Also included is a parking brake...

This engine was built for me buy Tico racing in Somerset Center Mi.(now retired and no longer in business) several years ago with the intent of putting it in a duster. I realized awhile back that I am not going to use this motor, you know plans and ideas change. So here's what l'm selling 373 ci...

Doing some spring cleaning and these are in the way and need to go. These are all from a 76 slant 6 duster, the car had just under 65k mi. The center link has light pitting on the ends and is powder coated black, the torsion bars are slant 6 .990 dia. one has some light pitting and are painted...

Never installed Hughes Performance transmission shield for a 727 transmission any body style I picked this up with some other parts and I don't need this. This is an older style compared to what Hughes is selling now but I don't know how old. Both pieces are aluminum, and there is no hardware or...

cast on 1/21/71 std. bore can still see cross hatch. Stamping on pass side oilpan rail is hard to read (stamping is not real clear) but it looks like 7G239789. I don't know what rods or mains are I have not pulled either caps. There is a windage tray, motor mounts, heads(cast#3671587) balancer...

340 block cast in 1971 it currently has std. bore not sure on the crankshaft. No camshaft, lifters, pushrods or, or valve covers. The timing chain cover balancer motor mounts cylinder heads waterpump and crank pulley are there. Small block 727 trans has flex plate torque converter (stock...

I have a K-frame that is 100% perimeter welded, boxed in steering mount for added stiffness to help eliminate flex. Also all factory weelds have been ground down and rewelded, lower control arm mounts and front strut bar mount have been reinforced just like the firm feel K-frame. I Added a skid...

Parking brake assembly with cable came out of a 76 duster, it worked good before removal no binding or sticky areas the cable is not seized up, the rubber foot pad is in nice condition along with the release handle. All that is needed is some paint on the foot lever and a cleaning. And it could...

For people that would like to convert to a manual transmission I have a clutch brake pedal assembly out of a 76 duster that includes the brake switch, clutch safety switch, push rod for manual brake master cyl. This assembly has light surface rust real nice pads on both pedals. I am also...

All aluminum forward strut bars adjustable. asking $150 plus shipping tom

76 A-body lower control arms with stiffening plate welded on ready for powder coating or paint asking $90. plus shipping. Tom

Bought a hemidenny K so I'm selling a 76 /6 duster modified K-frame per schumacher specifications full seam welded same as firm feel, steering box gusseted, engine torque strap and motor mounts included and skid plate welded on. All powder coated black. The K-frame if you were to buy from firm...

Never used TTI headers (p#TTI340A-C4) still in box. I'm taking my build in a new direction (lowering car to the point the headers will scrape the ground) and these headers won't work for me without heavy modification. At this point it would be better off going with a custom bent set. Everything...

I have a set of tti headers still in an unopened box for sale pt# tti340A-C4. These are 1 5/8 x 1 3/4 step header w/3" 3bolt collector flange that have a ceramic coating and the thermal barrier applied. These will fit 67-76 A-bodies with 273-408 ci. small blocks. I am located in Michigan (49509...

Looking for the rubber block that the window sits on when down all the way it sits in the bottom of the door they are approx. 1 1/2" x 1 1/2" x 2 1/2" with a tab on bottom.please pm if you have any. These any 70's A body should have them,

I'm looking for the black plastic splash guards that mount to the fire wall to prevent water,stones,dust from hitting the doors. If you have a set please pm me. For a 76 duster and im sure there are earlier years that use these just not sure if they started using them in 1970.