Search results for query: *

I'm doing an EFI conversion on a '65 Dart GT convertible. I was going to convert to a GM CS alternator but realized it has the old pump and pulley setup. I'll go with a replacement OE style alternator but the lower bracket (slide) is a hacked up piece. I'll buy the the set up with hardware if...

So here it is... My '68 fastback, solid AZ body with 2"x3" front rails from the rear crossmember forward , uses stock upper shock and control arm perches and k frame mounts. Frame was done in the 70's and I bought it with the stock disc front end. It was a 70's custom with a steel tilt nose that...

I'm using a 2004 truck cover and appropriate ATI balancer per ATI tech(early truck ,no vvt or mds). The block is a 6.1. I've got all kinds of conflicting info on which side of the new design seal is the air side. They are not labeled and the cover was bare when I bought it. The obvious choice...

I'm starting the process of converting my 408 to a 6.1/426. Can anyone give me the measurement from the intake mounting surface or an aftermarket intake top, to the hood line. Preferably in a 67-69 Barracuda. I have no inner fenders so I need either the intake surface to a hole in the hood or...

Any one going to Hemmings Musclepalooza at Lebanon Valley this Sunday? I did both last year and had a blast. 3 different ways to enter your ride (show, show and race or race only) with the show field split for dual duty rides and the dedicated pit area separate. The weather is supposed to be...

Musclepalooza XXVIII (28) this Sunday at Lebanon Valley ,NY. I went in May to #27 and had a blast. I signed up for race and show, got some timed runs and parked it in the show. https://www.hemmings.com/musclepalooza

This weekend, it's all makes, Muscle cars only with drag racing and show cars. I can't figure out how to link. It's on both of their website calendar of events though.

1 set of matched 500cfm manual choke AFB's.9305S's They were used as duals in my 68 r/t with a mild 440 with a MP509 cam on an Offy low rise dual quad 360 intake(went to EFI 505"). Progressive linkage wasn't needed and come with the connecting link that will connect to the factory cable. I just...

Throwing this out there while the engine is out. This is a done car that weighs 2950# with 1500 even on the nose. Car was finished last summer and has 1600 miles (drives anywhere).Solid AZ body fresh Chromabase paint. VFN glass tilt/lift off nose with stock grills. Jeep headlight buckets and...

So I took the car to E-town Mopar show for the first time. I planned on making some time runs and if all went well park it in the show and make it a day. The first 3 passes in this car since finished netted an 11.4,11.3 and a shut down at 1000' 11.4 . I didn't want to screw up the cars racing in...

1 set of matched 500cfm manual choke AFB's. They were used as duals in my 68 r/t with a mild 440 with a MP509 cam on an Offy low rise dual quad 360 intake(went to EFI 505"). Progressive linkage wasn't needed and come with the connecting link that will connect to the factory cable. I just...

I bought these to use and found they will not fit Billet Specialties Street Lite 15x10's, the rotor lug holes are opened to fit Moser studs 5/8" knurl but are hub centric and won't be affected by stock studs. Only 1 caliper was bolted up and has a slight scuff on the pad access area from hitting...

right side forward lower patch panel from door jamb to wheel opening. $30 plus shipping. Thanks,Keith

1 set of 4 k frame bolts smoothed and chromed back in the day in great shape $22 shipped. thanks, Keith

I purchased these years ago for my Coronet when it had a mild 440. bolted them on and found right side shock tower interference. No clearancing was done. Probably not recommended for RB's in any unmodified bay . They barely touched so B's wouldn't be an issue I changed them before starting the...

1 set of Laysons 1968 barracuda stainless trunk moldings, They are everything his ad says and are definitely sturdier than the originals. They come with almost all of the retainers. 2 of the Layson reatiners cracked . I acquired OE pieces which are lighter. The picture is of the actual pieces...

new never installed mopar p3690732 conversion regulator. $25 shipped. Thanks

I bought it bolted it to the firewall and switched efi systems without ever putting a connector to it. I purchased it years ago for my last build and went to a protuner efi system (edelbrock). $40 plus shipping .Thanks

2- 2-1/2" id 10" 225-475# progressive rate springs #10dp225/475 2- 2-1/2" id 9" 300# springs springs were not driven on , just installed to check setup and removed. $50 per set or $90 for all four plus shipping. Thanks

afco 3845cb2 single adjustable aluminum coilovers with 250# springs, came with my control freak kit only bolted on to check ride height, never driven on . 12.25-13.25" ride height 4" stroke. $260 for the set plus shipping.

manual box to p/s column adapter $50 shipped

set of rear pillar dome lenses, very minor pitting, overall nice shape $25 shipped

set of 10 bow end retainers and 2 tension springs for a fastback $20 shipped

complete set with 1 broken stud. $45 plus shipping from 11753 ny

from my '68 barracuda, missing lower bearing lock screw, $100 without wheel $125 with, plus shipping, thanks

manual box from my '68, pictured as it was removed from the k-frame (K sold) $65 plus shipping, thanks

this is from my '68 with KH front disc. It came with the car and I haven't tried it. I went Wilwoods all around with a late mopar style MC. Chromed in the '70's. Good for rebuild or power to manual conversion or front drum to KH conversion. $25 plus shipping, thanks,

came with the car , chromed in the '70's, straight no rust,grease or damage. will consider separating. I would prefer complete sale and reduce price for local pick up.$200 for all plus shipping. disassembled it can be ups'd. kvan408@gmail.com Thanks, I also have the column that went with it

really nice set of chromed front bumper brackets from my 1968 barracuda $50 plus shipping.thanks kvan408@gmail.com

set of 16 comp magnum 7623 pushrods, ball style ends, straight, no wear, 500 miles,I changed lifters. rods are 5/16" hollow ,6.750". $60 shipped. Thanks kvan408@gmail.com