Search results for query: *

I’m looking for one in good condition for 360 LA block. Thanks for the help.

Parting out a complete 67 Cuda that was used for body only. I have many parts. Here’s the power train that ran well. $300 pick up only in Orange County 92887.

Very good condition $80 +shipping located in SoCal

I have a 9 1/2 inch 727 converter with 3800 flash stall I would like to sell. Only 1500 miles on it. $225 it has very nice street ability. Just too loose cruising highway with my setup.

Just installed a 727 with reverse manual on my 67 coronet. Is there a ratchet shifter out there that will plug into stock console?

Looking to buy 2 kmember bolts and washers. 67 bbody. Thanks

Anyone know of an electric system that doesn't require pulley integration? Or is there a way to set up a pulley driven pump with power steering and alternator on a 440?

Running a 512 ci 670hp and 690TQ 6000 RPM motor with 2 1/2 inch exhaust running through flow masters. Everything I've read says I need 3" exhaust to max top end. Any thoughts?

I pulled my pan off 408 LA block (fresh build) to fix a small pan leak and there was fresh clean water/coolant in the pan. Appears to be dripping down from front of engine by #1 cylinder. Took valve covers off and oil is clean. Can't figure it out because engine ran great and oil was clean...

I was having fuel starvation issues at all speeds. Found that my new gas tank had dumped a bunch of gunk into both filters. Now that I have cleaned both filters I am still getting a starvation issue at Hwy speeds when I give it WOT. I'm thinking the pump may have gunk in it. Thoughts? Is this...

I just got my brand new 512 running today. Only a short 20 mile ride from the installer to my house and got home to find everything covered in engine oil from front to trans. Total FUBAR. All brand new parts covered in oil. Brand new headers wasted. The builder gave me one breather on drivers...

It's a joke. I've been running air bags for a couple years and nothing but problems. Just wanted to give heads up. Air Ride sucks.

I'm having Joe Sherman build me a 512 stroker for the 67 coronet. Anyone want to take a guess at the dyno numbers we will get. 512 scat assembly Eddy victor heads 355cfm on bench Super victor single plane intake 1.6 roller rockers Comp custom full Hyd roller -- 242-- 248---590 lift---111...

Anyone running a stroked 440 (528ci)? I am having one built for my 67' coronet and will be 700+ HP and concerned on the cooling. I know there are lots of variables but just looking for someone thats running a big monster on the street and keeping it cool. Here is what I will have 1. Champion 3...

Just wired the 67 coronet with an ezwire universal harness. Everything works perfect except headlights. The outside lights are bright and work but the inside light barely has any light at all. High beam or low beam doesn't matter. Any ideas?

I have a 67 Coronet. Will a 440 with eddy RPM intake and holley carb clear a stock hood?

I've got a 440 that I picked up with fresh build but want to get more out of it with upgrading to aluminum heads, intake, cam and carb upgrade. Biggest question is heads and which intake to go with. I would prefer to get heads ready to go so who ports the best? This is a street car and I want...

Having issues with 440 timing in a 67 coronet. It was pinging awful so I tried a few things and now it's not pinging but a bit sluggish and rough idle. Also running hotter. I have 10degrees initial and 28 advance. When I retarded the initial from 15 to 10 it was bad but then I added 10 degrees...

My 67 coronet had a round back alt with 2 wires and external regulator. Anyone know what I need to do to convert to one wire with internal regulator?

I have a set of magnum wheels in good condition. 8 inch front with new 215/70 r14 9 inch rear with Mickey Thompsons that are cracking but good tread. The wheels are in good condition. $250 in Southern California. I would rather not have to ship them.

I just purchased this car and will be installing an alterkation in the next month. Below is a list of parts I will have for sale once I pull them out. The stuff is located in SoCal and I would prefer to sell there if possible to avoid shipping hassles. The parts look very low miles and can be...

I just ordered an alter k for my 67 coronet. I'm going to install without pulling motor. Any tips on doing so? How did you support the motor with kmember out?

I just picked up a 440 with M1 on a purple shaft street hemi cam with 906 ported heads. 750 carter carb My engine builder says go 850 Holley with eddy performer heads and air gap. Do you agree? FYI this guy is Joe Sherman and will port these heads as well as anyone IMO

750 AFB that's stumbles off idle. How do I increase acellerator pump squirt etc?

Just picked up a coronet with a built 440 but pinging and off idle hesitation. It's got a vacuum dizzy and specs below. Any quick tips to troubleshoot? Also, I'm curious if I should go MSD, aluminum heads with roller rockers. Would i see a big HP gain? Here are the basics. Engine: 1964 440...

Looking for a straight body project 67-74 Cuda or Dart. Planning on building from ground up but do not want to do any body work. A paint ready roller would be ideal. Thanks

I have a QFT and want to dial in secondaries. I opened the adjustment screw 1/4 and it made a positive impact. Any tips on how to find the sweet spot for vacuum secondaries?

Your Ad was deleted by staff. Please review the "for sale forum" rules before posting again.

I have a brand new pair of brushed aluminum valve covers with hardware. $70+ $10 shipping.

Your Ad was deleted by staff. Please review the "for sale forum" rules before posting again.