Search results for query: *

What’s the date code on this? 1572 some the research I seen it’s from 1992?

Hey guys I been reading up on Holley seems like there’s two ways to select a power valve, which one do you guys use? In gear warmed up I am at 15 inches of mercury and cruising light throttle I am at 22 inch or mercury

$120 Shipped USA Only was pulled of my running car before it got junked

Looking for a complete carb to rebuild or a runner! Shipped to 91770 thanks!

Carb is very clean inside ran great, also includes the calibration kit as well $250 shipped

Looking for a running projected thanks!

Looking for a set up in the Los Angeles area

Hey guys on my 64 dart the quarter window and the driver side window do not align correctly and leave a opening up top any idea how I can fix this?

Really good unit low miles $350 can ship for $120.00 located in Los Angeles

Pretty clean trunk and passenger door Located in Los Angeles $100 door $200 Trunk with gt trim pick up only

Later 318 water pump 1970 and up aluminum bottom one was paint black $80.00 shipped

73 340 driver side 2 1/4 outlet and 93 Dakota passenger side manifold 2 1/8 out let with head pipes to fit automatic trans with manual or power steering. Located in Los Angeles $500 for everything

Looking for a good unit shipped to 91770 thanks!

I’m going to install a 600 cfm Holley on my mild 318 carb I wanna know if I should already order different jets and power valves right off the bat for my engine the carb specs are stock 600 cfm Holley power valve 6.5 primary pump nozzle 31 primary jet 66 my engine is a 318 Magnum, 264 duration...

Complete set up head pipes for 67-72 a body small block 73 340 driver side 2 1/4 outlet 5.9 magnum 2 1/8 outlet exhaust will fit manual or power automatic transmission only. Comes with hardware etc $450 Local pick up Los Angeles can ship on your dime!

I think my motor mounts are switch over not sure what do you guys think

Formula S?

Just installed these summit $260 headers on my 1967 Barracuda, honestly pretty impressed! 318 with magnum heads, manual steering manual brakes The Good 1.the quality on the flanges were great 3/8 thick flat flange all the way across not like what’s show in the picture Online. 2.Came with...

So I got these headers on offer up for $100 he said in add small block headers mopar. I knew right off the bat they weren’t hookers lol they have one slip tube on the #7 tube the closest picture I found that had a slip tube were these TTI headers I couldn’t find Doug’s with a slip tube online...

Hey guys two questions, first do I have to remove my engine to tran brace to install headers? second question can I still run my short oil filter with no 90 degree adapter? All the other stuff I know what I have to do with the center link lifting motor etc just don’t remeber these two things...

With 3.23 gears in California thanks!

Hey, looking for a 64-69 small block crank pulley 2 groove diameter of the last groove towards radiator is 6 3/4, let me know shipped 91770 Thanks FABO!!!

Looking for a holley 600 cfm carb that’s ready to run going to slap it on my mild 318 shipped to 91770

Hi, looking for a water pump pulley and harmonic balancer pulley no power steering no ac 1968 273 318 shipped to 91770 thanks

Installing one trunk torsion bar after it snapped, any tricks or tips on how to do this looks like a lot of force is required to get them into place. Would it be easier with the trunk off?

Shipped to 91770

Cast crank block (1978) lighter slant six block $20.00 in Los Angeles cast crank , took it all apart comes with crank/ rods pistons /block was .020

$60for everything plus shipping in large flat rate box US only mostly 64 dart gt parts and a little bit of 65 dart trim im throwing in paypal only USA shipping only

looking for a 7.25 with 3.23 gears in SO CAL thanks!

Hey guys so pretty sure your guys know aftermarket aluminum radiators in a early a with a slant six is a pain in the ***. Reason being that champion does not have the correct core spacing. 1.What I did is had to cut off the radiator mounting brackets and welded them back 3/4 of an inch so I can...