Search results for query: *

I have a 741 Rear chunk w/2.93 gears. The bearings were all replaced new, spins freely, needs final setup. I ended up getting hold of a 742 and installed that instead, after having gone through this one and rebuilding. $200 I also have a brand new-in-box and still wrapped A-Body gas tank for...

This was mistakenly advertised as an A-Body axle when I bought it, but it is really a B-body axle, so I cannot use it. It measures 55" from outside flange to outside flange. It had some surface pitting, but is otherwise solid, so it would be for a driver only. I throughly cleaned it inside...

This is out of a '69 Barracuda convertible, but I think it will fit 1967-69 too. It is in good shape for a driver, no chips or scratches on the surface or edges. It has the tint at the top. I don't need it, and I'd rather see someone make use of it than throw it away. I can't ship it though...

Various parts to a rearview mirror. The mirror itself is original, taken off a '69 Barracuda. It is in good shape, as shown in the pictures. The post is not original, and has some nicks in it, but overall in good shape. The base is new and unused, but does not have the ball for the post to...

Set of tail lights taken off a '69 Barracuda. Driver quality, they need some work, as can be seen in the pictures. One has cracked lens, the other is intact. One has a small ding on the chrome. Pictures show what you are getting. $45 plus shipping.

Looking for the whole assembly for a 69 Barracuda in decent shape. Anyone have?

So, here is the situation: 69' Barracuda, all new dash harness, new turn signal switch. When I put the turn signals on, the rear ones flash fine, the front ones do not light up at all (on either side). Same with the hazard lights - rear work, front do not. What's really confusing me, though...

Hi all, I seem to have limited choices here on Staten Island for having a convertible top installed. Has anyone had any good experiences with an installer nearby? I don't want to just go to a shop without some recommendations. Willing to travel a bit for the right job and a fair install...

I have read a few threads on this topic, but can't seem to get a clear answer from existing threads, so I figured I'd just ask. I have a peg-leg 741 differential with axles that have been changed over to green bearings. Upon installation, I found that the axles wouldn't seat, and so researching...

Hi All, I have a 69 Barracuda convertible and reupholstered my seats in white from Legendary, and have the door panels/sunvisors to match. I'm trying to figure out what shade of white to paint the side panels, as I'd like to avoid the dreaded multi-color white interior. I bought a can of...

These are for bucket seats. Removed from a 69 Barracuda, they should also fit for at least 68-70 seats (others too?). Chrome needs to be redone, but fine for a driver. Two of the plastic rings have hairline cracks (see pic), but all other parts are solid. Since the headrests aren't made to move...

Pair of white (sort of) headrests out of a 69 Barracuda, but should fit bucket seats from 68-70. These need to be completely redone. Can take additional pics if needed. I won't be reusing them, but I'm hoping someone wants to redo them and make use. $20+ship

Black dash pad off a '69 Barracuda with rallye dash, will fit other A-Body makes/years between 1969-76. Pad has one large cracks in the vinyl, a few smaller ones (see pics), but would be good for a driver or someone who can repair these things. Solid core otherwise, clean, if you want to get...

Set of four 215-70R14 Goodyear Wingfoot HP tires in good shape, along with the four steel rims, small-bolt pattern. The tires still have good tread on them, no gashes or issues. I had these on my Barracuda until the resto began, now I'm changing over to LBP in the spring, so I won't be needing...

Pair of fenders in need of repair, and two brand new patch panels (photos of all are below). Everything from a '69 Barracuda, but will fit 67-68 too (the fender marker lights are different). Driver's side fender: Is in need of serious repair, or it can be used for parts, especially the...

Solid set of shock plates and U-bolts for a 7-1/4" rear. $15+ship.

This is a late 60's 8-3/4" rear, measures 55" from flange to flange, 44" from center perch to center perch. I bought it for my Barracuda project, then changed direction, so I don't need it anymore. It was stripped, prepped, and painted, has new seals installed, and I fabricated new brake line...

Hi Guys, I am rebuilding the lower control arms on a 69 Barracuda. When I took everything apart, I found that I have two different pivot shafts. I am putting new rubber bushings and sleeves on, and my question is, does it matter that the two shafts are different? Before I start cleaning...

Off a 69 Barracuda, has the attachment pieces. $5+ship, or I can bring to Carlisle.

Pair of stock strut rods, need to be cleaned up. Off a 69 Barracuda. $10 + ship, pickup, or I can bring to Carlisle.

This is a pair of 10" front drum brake assemblies off a 69 Barracuda, which I was driving through last October. Includes spindles, brake parts, drums, and whatever else is still attached. Asking $125 + ship, or you can pick up. I have the upper control arms listed in a separate post, if you...

These are off a 69 Barracuda. Asking $50 + ship, or you can pick them up. I can also bring them to Carlisle for you, save on shipping.