Search results for query: *

C11 on rhe left and C12 on the right.

Should have an alpha/numeric code on the head, ex... C2

===>>> Horizontal listing 1st, fold the top down to access the wire then move to the sides. I started from the center length of the wire and worked toward the ends. Pretend your making a breakfast burrito top/side/side then flip the seat over and work the back/bottom. If you don't have them...

Clean up the frames with a angle grinder wire wheel as best as possible and paint. Install the covers with each side folded up in the FINAL position before hog ringing the listing wires. Do you have/need the horizontal listing wires for the backs? Are you installing headrests? Legendary...

My son and son in law, I help them whenever possible.

Left lower Left front behind the headlight, see it on the left side above the bumper bracket

Back story...... https://www.forabodiesonly.com/mopar/threads/small-hard-line-to-1970-duster-front-10-drums.559950/#post-1974651876

There is some gaping from chain stretch, is it too much,I don't know.

Photos required, please. Lets see the sprockets.

I used the stock spings with the comp .480

This is what I used on my Edelbrock Airgap with no issues. No china wall gaskets. Get a good phenolic spacer for under the carb, Edelbrock has these also. Check out the Holley web site for parts. https://www.edelbrock.com/intake-manifold-gasket-for-for-1966-87-318-340-360-chrysler-engines-7276.html

What intake, iron or aluminium? Ported or stock? 2 or 4 or 6 or 8 barrel, high rise, mid or low. Dont know that it matters but it does make the conversation a bit spicer!

Looks like you either hit something or a backfire!

I have 2 sets of slant 6 w/air-318 2535890-891/325 0.85 101#/in 2071624-625/135 0.85 101#/in

:popcorn:

I have cracked brand new plugs while installing them! Need to keep the socket and extension as straight as possible if that's the issue.

I think @ratty dart 340 is looking for something like this, only the rod

What part did you buy and name the seller. Cheers

Bucket or bench, it matters.

I wont buy from face regardless, but, you paid the extra $100 anyway? knowing it was a scam?

VIN# off the block and the #'s below the drivers head at the front of the block

Post a want ad for 2 or 4 barrel and see what kind or responses you get then go from there! https://www.forabodiesonly.com/mopar/forums/cars-and-mopar-parts-wanted.15/?order=post_date&direction=desc

You can use the two barrel Rod which is a lot less expensive than the four barrel, go to Ace Hardware or Tractor Supply get a piece of thread all and a barrel nut you're all set. You're basically extending the two barrel Rod by this amount roughly an inch or so . That will give you the...

Most of what I have in my Stock portfolio are very low vs initial investment time. I am willing to wait these out. I also have a Fidelity market IRA which has made a comeback recently with the "No Fee" funds and the 401k has recovered and surpassed previous highs fortunately. Several IRA CD's...

For the Holley you're also going to need this bracket and the stud. https://www.holley.com/products/fuel_systems/carburetor_components/brackets_and_linkage/parts/20-7

Specifications? Lug Bolt pattern Gear ratio Differential configuration: open or closed

Post a photo(s) of your configuration for the best diagnosis.

Location?

Good Mornin Brooks, I am looking for either of these, pretty sure we didnt talk about these :) 2852206 1967-69 2.75 48.60" 904 8-3/4 273 318 Barracuda Valiant 2852206 1967-69 2.75 48.60" 833 8-3/4 273 318 340 383 Barracuda Valiant Art

Post a photo or two.