Search results for query: *

Hello all, looking for an original working gas sending unit to a 1965 Barracuda. Thanks, Larry

Hello all, Looking for an A body fan shroud to fit a 22" radiator for a 318, 340.over all size from bracket to bracket is 26". Please pm me.

Hello all, need pictures posted of a 1970 , 71 federal pump w / bracket installed in a 340 motor a body. Thanks..

Wanted, 1971 , 72 318, 340 small block working power steering pump with brackets. Thanks

Hello All, I'm looking for the steering column mounting bracket for a 1965 barracuda. Bottom piece that bolts the column in and stops it from moving. Thanks, Larry

Hello, I'm in need of a 18 spline 904 torque convertor. Need it for a. 65 ,66, 67 v8. Thanks. :burnout:

Hi, Looking for a 1965 Barracuda (904) torque convertor. Please send PM. Thank you, Larry

Hello, looking for a working wiper switch (2 speed) to fit a 65 barracuda. Thanks, larry

Hello All, I have a 65 barracuda that when the engine is running my windshield wippers turn 3-4 times then I hear a clicck from my wiper switch, I turn off the wiper switch than it restarts, when engine is off wiper dont click off.. Larry

Hello all, im looking for a set of 64,65 barracuda head light bezels. thanks.

Hello, im looking for a drive shaft to fit a 1966 barracuda with an 8 3/4 rear end. Thank you, Larry

Hi all, I'm now selling my 273 motor and 904 transmission to my 1965 Barracuda, both have been rebuilt ( 6-15-14) and installed in my 1965 Barracuda 8-17-14. Its been driven around 2,000 mile with 3 oil changes every 600-700 mile. I'm selling because I'm putting in a rebuilt 340 ( 1968...

Hello All, Im changing the Transmission on my 1965 Barracuda to a later model 904, I've order the shifter cable from Imperal so that my original shifter can hook up to the new trans. My question is what about the speedometer cable? will I need to change to a 1966 cable or will mine work? If...

I'm in need of the fresh air inlet door ( drivers side) to a 1965 barracuda. Thanks.

Hi, looking for a good condition 8 3/4 suregrip 3.23 gears Center section. This is for an A body rearend. Im located in Florida so must be willing to ship. Thanks

Hi, :director: Im looking to buy a radiator to a 1965 Barracuda V8, Good condition, No leaks. I'd have to have it shipped to West Palm Beach Fl. Please PM me if you have one available. Larry

Hi, Looking for a 1965 barracuda wiper switch. Thanks

Looking for a 1968 barracuda grill in good shape. thanks

Hi all, Im looking for axles for a 8 3/4 A body 5×4 bolt pattern, not bent and the bearings on the axles are good. Thanx!

Hi, Can someone tell me what an original stall is on a 1965 Barracuda (273) torque convertor? Thanx!

Hi all, what higher stall convertor will fit a 65 barracuda (273), I'd like it to be 2000-2300 if possible. Or, is this something that has to be made as I know the splines are different... Any thoughts?

Hello all, I have a 65 barracuda with American racing rims 15 x 7 , Question is what is the largest rear tire I can put on this rim without it rubbing... Also, on the front I would like thinner tires, any suggestions? Thanks in advance to all.

What's the rpm operation of a standard Torque convertor from a 1965 (273) barracuda V8 / not hi-po with original cam

I'm looking for a Torque convertor (2000-2500) for a 1965 273 barracuda.

Ok, need some advice on what you guys think I can do to make my car run better. I just started a rebuilt 273 from a 1965 barracuda (automatic). What I have in it are the following; bored .30 over / 10.1 pistons / dont remember what type. 302 swirl port heads / rebuilt with the bigger...

Hello all, I'm in need of a Alternator bracket for a [273] 1965 Barracuda. Complete if possible. Thanx.

Hello, Can someone shoot a close up of a [273] 1965 barracuda auto. starter relay with the wires connected. Thanks

Sorry cant seem to upload pic's. Here they are.

Hi, I've attached a few pictures of wires on my 65 Barracuda that I can't figuere out. One is by the bulk head and the others are hooked up to the wire that go to the altenator and temp gauge. I've hooked up the alt. and temp gauge wire but on the same line are two more wires that I have no...

Hi, Can someone shoot me a picture of the power steering pump and brackets installed in a 1965 Barracuda 273. Trying to put mine together. Thanx!:banghead: