Search results for query: *

Hi, I am in the process of putting new seats into my 71, a bucket set front & rear from a 72. On the rear upright, I have noticed a tab / bracket that looks like it fits to the body floor - is that correct as they isn't a hole / fixing on my floor.... Am I right in saying that the 72...

Long shot request, as title - WHY? Thanks:D

Long shot request, as title - WHY? Thanks:D

Hi y'all! I am in the process of getting our 66 valiant running after fitting a 273 (67 I think) and 904 trans. I have fitted the starter (can't remember if it came with the motor or not) and it does not appear to mesh with the ring gear? The ring gear does not seem to be worn. The socket...

As the title says, anyone??

Hi, I need to make a brake line from may new master cylinder to the splitter block. Could someone tell me what size / diamter this line should be (if not 3/16) and what size fittings I need? Manual single circuit brakes. The existing MC does not have a line so have nothing to compare with? TIA

Hi, I have a 66 Val. I am current running new brake lines throughout. There is an male to female inverse flare adapter on the end of the brake master cylinder that could do with replacing. Could anyone tell me what size it is? TIA

Are these still being made? - does anyone have any that they are willing to sell?

As the title says or information if repro is available TIA:wink:

Would any know where I would get a rear gasket for the about. Is this the same as any other model? TIA

As the title says, WHY? Other parts also required for 66 Valiant 2dr post TIA!

As the title says, for a 66 Valiant post Willing to cover shipping to Iowa TIA

Hi, Have a block here that I need to check out for wear etc. 1. Once the rigde is cleaned, this will give me the original bore diameter - correct? 2. Measure just below the ridge where the rings meet will give me the bore diameter plus bore wear - correct? The motor I am looking at I...

Hi, hope someone might be able to help me here...... I have a 66 Val on it's way. The Hood, rear screen and bumpers are missing. Are any of these found on other models? My help me in my search knowing that these items may be found on other Mopars...... It was originally a 6 Cyl Car - what...

Hi, I have a 67 Valiant 100 on its way (I hope!) and lookin for inspiration.... Want to go Old Skool Gasser with this - has anyone any pics of a similar machine for inspiration? TIA

Half set required 4-left & 4-right. Would consider full set - WHY? Thanks 8)

Hi, Having problems with my Indictaor lights here - left hand Front does not illuminate, and left hand rear does but does not flash. Right hand work perfectly. Does anyone out there have a diagram showing the switching of the Turn signal switch (71 A Body) Thanks

Hi All, I am in the process of rebuilding the front end, and have removed motor & front suspension etc. Before I powder coat my K Frame (/6 with schumacher mounts for B motor) are there any mods that can be done - is the any potential for any weight removal? Any information would be...

Hi Everyone, I have a 71 Duster (originally a /6 car) fitted with disc brakes. I am trying to identify parts so I can order the right Willwood kit and replace the Upper ball joints. The rotors are Unicast (1 piece) and are a fraction under 11" so these are 10.87"? The calipers are the...

Hi Everyone:thumbup: Recently bought a 3400 stall convertor for my 383 Duster. BUT, with the footbrake applied, I can only really get say 2K before the rear end starts to hook......... Am I missing something here or do I have a bad vertor:dontknow:

Hi Newbie Here:wave: Does anyone know if anyone reproduces the chrome trim that fits in the rubber windsheild gasket? For 71 Duster