Search results for query: *

Has anyone dealt with Magnum Force Suspentions? I've been looking at there front Coil Over Tubular conversion, a bit costly but it does look like it is well made. Any info or thoughts would be appreciated. Thanks Ken

I need a right, passenger side, bumper mounting bracket for a 74 Plymouth Scamp with a 71 Duster front. 'Driver quality' is fine, some surface rust is OK as long as it isn't pitted or bent. Thanks, Ken

In need of a right side, Passenger side, bumper mounting bracket for a Plymouth Scamp, Duster. It is a 74 scamp with duster front. Doesn't need to be perfect, surface rust ok as long as it is not pitted or bent, driver quality is fine. Thanks, Ken

There should be a bunch of these out there, I need the alignment pins/studs for the block to the tranny. If it matters for a 340 to 727. Help if you can... Thanks Ken

I had a small problem, I wanted too many gauges but didn't have enough 'dash' to put them in. I wanted no heater, no radio, no ash tray (Switches will go in a panel where the ashtray was), just the stripped down car (light weight) a built motor, tranny and rear. Well I have a bored and stroked...

Has anyone gone to the disc kit by Wilwood (140-15468-DR) And have any opinion. Wilwood Disc Brakes - Front Brake Kit Part No: 140-15468-DR My Scamp has the 'factory' disc's from a '73. I have ordered the Wilwood 'Big Brake Kit Forged Dynalite' for the front, with the SS Braided 18" Lines...

As stated I just need the dash from the standard A-body, not the gauges just the part pictured. There has to be dozens of these things laying around! Like this... THANKS, Ken Sua Sponte RLTW

MY ERRROR... IT WOULD NEED TO BE A 1973. This is an alternative to not being able to find a GOOD complete door. I will attempt to explain. I would like to get the "inside" part of the passenger side of a door. The car was a 'Drag Car' all of it's life and as such the Body is...

MY ERRROR... IT WOULD NEED TO BE A 1973. This is an alternative to not being able to find a GOOD complete door. I will attempt to explain. I would like to get the "inside" part of the passenger side of a door. The car was a 'Drag Car' all of it's life and as such the Body is excellent,but...

Would like to find one in the Arizona area, I'm in Cottonwood (near Sedona) but willing to drive to pick one up. 'Driver Quality' is all I need, just don't want one pre-dented.... Would prefer witout jack-slots. Thanks Ken

This has most likely been asked a dozen times, but I can not find it here with a search... So please, Will a '70-'72 Duster Grill work in a '73 Scamp? Will much have to be changed? Ken

Need two 'Scamp' fender emblems, driver quality is fine, do not need to be perfect. Thanks, Ken

I need SPOOL type motor mounts (left and right sides) to put a 1969 340 in a 1973/74 Scamp.

I have a 340, 1969, w/X heads It is stock bore, No ridge at top of bore, crank never turned Supposedly about 68K miles when pulled out and been sitting. Yes it is clean, not a rusty POS, just some varnish like dried oil in it. It did turn over at the crank. I'm taking it apart and to have...

The inlet fuel fill tube that is on the left rear fender, routes thru the trunk area and goes into the fuel tank. I believe most are the same, mine is a '73 Scamp. Thanks, Ken

I am wanting/needing/desireing/searching/ a 8.75 for my Scamp. One narrowed even better! The reason I'm asking here is I don't want to have to go to some where like North Carolina to find one!!! Some one in Arizona has to have one lying around just gathering dust, or rust...

Needed; (specific) CARTER 4936 S with an Idle stop solenoid Ken RLTW

Parts for a small block 727, 340 engine Flex plate Inspection cover Fill tube and dipstick Thanks' Ken RLTW

A simple request. Need a SB 727, along with everything from the crank shaft back, flex plate, TC, ect. Really trying to find one in Arizona; Presscott, Phx, Flag... I'm near Sedona. Yes, I HAVE been checking Craigslist. Thanks in advance. Ken RLTW

Willing to go to Prescott, Phx or Flag... I'm near Sedona, in Cottonwood. Some one has to have them laying around somewhere!!! lol Yes, I've been watching Craigslist. NEED; a flexplate, Inspection cover, Filltube & Dipstick Fortunately I found a new friend just a couple miles away that had a...

I just had to tell someone! My neighbor (Mark) that owns a Polaris dealership here and is always finding deals and trades for RZR's. He was showing me one he bought outright from some guy that was moving and selling most everything, the guy sold it for less than a third of it's value!!! He...

Looking for a small block 727 transmission, local in Arizona. Would like it complete with flex plate, TQ converter... A decent builder would be fine. Ken

OK, I admit it, I'm new to this "a-Body" world !!! I will have other questions along the way that will probably irritate some here but how else would I get the answers to what I'm not sure of and thought this woud be the reason for this forum; to help those with 'questions' that may be basic...

In need of a GOOD passenger side door (2 door model) for a '73... yes '73 Also need a Good front bumper and mounting brackets for a '71... yes '71

Are the small block intakes for 318, 340 and 360 all interchangeable. I.E. A Weiand Dual Quad Tunnel Ram, number 5995 ?

Need a good Passenger side door for a 73 Scamp, I do not need the glass, just the door with working glass mechanism and opening mechanism. PLEASE, let me know if you would have such a thing! Thanks, Ken

First, I'm Retired. This IS my first post. Now that is out of the way, I just picked up a really clean '73 Scamp body (roller) I also grabed another '71 Scamp w/a Very clean body. NO rust on either one. Ya gotta love AZ. The '73 had been a Drag Race car for many, many years and is set up for...