Search results for query: *

1972 Duster 340 for sale. Matching numbers engine and 727 transmission. . Car has approx. 43, 000 miles on chasis and has been completey restored. New interior; dash, headliner, carpet and has original seats/stitching. Hemi orange. Original punch card. 3;91 sure-grip. new trunk mats. This is a...

It doesn't vibrate at idle, but starts ossilating around 55MPH tapers of then again at arond 75

I've done everthing to try to find the vibration, and I'm just wonderiing it's a 72 340 with a forged crank (interanlly balanced) could it be that (1)I have a torque converter that has balancing weights causing the problem or (2) the harmonic balancer is drilled for balancing, and maybe it is...

n42 r11 v6w v8w en2 ev2 v g33 m21 n23 n41 ev2 c4xw tx9 c08 274978 e55 d34 vs29 h2b 259518

1972 Duster 340, matching numbers and 43000 mile on car. Original Hemi Orange, 3:91 suregrip, torqueflight. No rust car. over $25k spent on bringing it back. Have original Thermoquad carb (not on car) and original manufacturer assemblyline punch list. All new wiring harnesses, front discs, white...

I'm still having vibration in the rear end of my 72 Duster. I have re-balanced the drive shaft, checked all the bearings (pinion/wheel)changed the third member, tires are balanced etc. and shimed the springs to be within the 4-5 degree tolerance. However, when we did the shimming it changed...

Found the problem of lost oil pressure. A rocker arm was busted in two.Never had this hapen before, but on close inspection you could see where the rocker arm was defective and had a hairline crack before it separated. FYI I could hear the valves clattering on one bank and that is how I noticed...

Yes I am interested just so the are LBP and the acornnut style for a 72. please send pics and price [email protected]

I need 4 Center caps for my 1972 Duster 340. These would be what are called the nut or acorn style for this change over year (1971-1972) these were also used on the Cuda/Challengers of the same era. Need to be large bolt pattern, 4 1/2". Send pics and price [email protected]

I've been running my 340 for about 200 miles and she's been doing real good. I had had a privious oil pressure issue and had solved it by replacing the oil pump, Now, all of a sudden (after a jack rabbit start) the oil pressue went way low 5-10psi, and the valvetrain is not oiling properly ...

How would you go about shimming the rear end and where would I find specs on this?

I am finishing-up my 72 Duster 340 and took it fo a drive and there is a very noticible ocilating vibration starting at 55mph and worse at higher speeds. The drive shaft was ballanced and still have the problem. Any body have thoughts that might be causing this; alaignment, bearings, drive...

I'm looking for a good sharktooth grille for my original 1972 Duster 340. Send pics and price. [email protected]

looking for center caps , large bolt pattern and the acorn nut style and 14" 6x trim rings for my 1972 uster 340. [email protected], I'm in NW Arkansas

do you have pictures? Is she in good shape w/the plastic mounts etc?

i need a drivers side remote mirror, in good shape with all clips and mounts for my 72 Duster

I have decided to put the engine/transmission in as a unit instead of separately into my Duster. Does anyone have some advise on doing this? WOuld it be necessary to undo the steering box etc?

I have put in the oil pump/ gear drive, but it doesn't seat completely on the bushing in the block, there is about a 1/32 nd gap. Someone said that the bushing should be deburred , which I can't do since the engine is already in. Does anyone have insite on this or a trick to seat the shaft, or...

I need a 90 degree oil filter adapter with bolt and gaskets for my 72' 340 Duster. I'm in Arkansas [email protected]

Looking for a radio preferably am/fm for early 70's Duster (72') [email protected]

i need enginesupport brackets for a 72 340 duster,

Converting a 72 Duster 340 from drum to disc brakes. I need spindles and understand that control arms my also be needed and that a 3 to 76 system may also work, Does anyone have some for sell? [email protected]

I've got a 72 Duster 340, converting from 4" drums to 4 1/2" bolt pattern discs. Does anyone know if the spindles on the drum system will work for this conversion, and if not what will, and if I need them does anyone out there have spindles that will work for sell