Search results for query: *

I’ve got the dash panel out of my 67 barracuda so I can clean everything, check the switches and wiring harness, replace the bulbs, etc. My car is an unrestored car that I bought off of the original owner this fall. The car had been stored in a Quonset for 30 years, and the mice had gotten into...

I have been chatting in the parts wanted forum with some members who suggested I move the discussion here in the electrical forum. I’ve removed the dash and gauges from my 67 barracuda for a refresh and a cleaning. I doubt anything has been removed since the factory as I bought this car from the...

I am refreshing the dash and gauge cluster on my 1967 barracuda. In taking the dash out some of the times on the back of these 2 switches were corroded and broke off and stayed in the harness connector, so I am needing a replacement wiper switch, and heater motor switch. If you have one or both...

I cleaned off the stamping on the left side of my 727 above the oil pan on my 67 barracuda 273 commando car. The number stamping are clear but seem a bit strange to me compared to B and E body automatic numbers that I’ve seen over the years. I thought I would throw the stamped numbers up to see...

I’m looking for opinions on how to proceed with a problem I have with the 273 commando engine that is matching numbers in my 67 formula S fastback barracuda that I bought recently. The car is an unrestored survivor, and the car has been stored inside for 30 years by the original owner whom I...

I’m slowly going through the mechanicals on my survivor 67 barracuda I bought from the original owner. The car had sat in a barn for 30 years or so. I’ve gone through the rear brakes and I’m about to get into the front disc brakes. Are there any tips or tricks on inspecting these calipers to...

I am needing a piece of trim for the rear of my 67 fastback barracuda. The rear trunk fold down divider has carpet on the inside, and the edge of the carpet is covered with black metal trim (4 pieces). I am missing the curved top piece that covers the drivers side top of the fold down divider...

The pinion seal on my 67 barracuda fastback is in need of changing. My rear end is a sure grip and still has the aluminum “use sure grip lube oil only” tag on the cover bolt. I’ve done lots of pinion seals on other cars and understand the whole marking the nut/yoke/pinion and counting exposed...

I am needing the drivers side thin rear sill plate for my 1967 barracuda fastback. The original one is badly corroded from mouse urine that had soaked the carpet up against it when it was in long term storage before I bought it. Here’s a photo of the passenger side one for reference. They are...

Firstly, merry Xmas and a happy new year to everyone here. I’m about to install a new carpet set into my 67 barracuda fastback. On the rear of the flip up seat, as well as along the top of the rear flip down plywood trunk divider, the old carpet has some slot screws with washers helping to hold...

The interior of my survivor 67 barracuda fastback that had been stored for 30 years is in great shape other than some of the interior that the mice got into. I am replacing the headliner and carpet, and that should be it other than the rear seat. There was a huge mouse nest packed under the rear...

I was lucky enough to have Bob on here sell me a pair of finned valve covers for the 273 4 bbl engine in my 67 formula S fastback ( they had been stolen when the car was in storage years ago). A couple of questions about freshening them up. What is the correct paint to use on the valve covers? I...

I recently bought a 67 formula S barracuda fastback off of the original owner, and he has the original bill of sale, dealership paperwork, brochures etc which is great. The radio antenna on this car is on the top of the rear passenger side quarter panel. This is an unrestored car, and clearly...

What were the factory wheel cover options on a 1967 barracuda formula S fastback?

I’m cleaning up the console top and flip up console door top on my 1967 barracuda formula S. Some of the greyish paint is missing, and I’m thinking I will repeat the grey to make it look better. Can anyone chime in with what would be the correct paint for the console top?

I recently was lucky enough to pick up a 1967 formula S barracuda from the original owner. While the car was being stored in a barn years ago, someone stole the 273 commando chrome air cleaner, and the finned valve covers so I am on the hunt for replacements so I can get this old survivor...