Search results for query: *

I have a 360 Long Block for sale. Block is bored 0.030" over and is assembled with new rods, pistons, Lunati Voodoo cam (specs in photo) and J casting cylinder heads. No rocker assembly or pushrods. Engine has not been run since rebuild in 2010. I had trouble sizing pushrods without bending...

I have an A-727 transmission for sale. Trans was set up for use with a lock up converter. Valve body has a Trans-go TF-2 shift kit installed. Trans should be gone through due to some intermittent shift issues I had over the 2000 miles that I put on it. Good core for rebuild. No converter. Asking...

I have a set of 587 casting Small Block heads for sale. Asking $300 but open to offers. Heads are in need of cleanup and potential rebuild. Local pickup in Fontana, CA (92336) preferred or I can meet in the local area.

I have various small block accessories and gaskets for sale. Part numbers, descriptions and prices listed below. All prices are plus shipping from Fontana, CA (92336) Carter M60514 Small Block Fuel Pump (used for 100 miles) - $10 A1 Cardone Remanufactured Saginaw Style Power Steering Pump...

I have a 670 CFM Holley Street Avenger carb for sale. Holley part number 0-80607. Carb was used for about 1000 miles. I pulled it off for a rebuild and switched to fuel injection instead. Fuel rail is stuck in fitting on the rear float bowl and the rear float bowl has been removed once. I have...

I have an Edelbrock Performer RPM Air Gap intake for LA engines for sale. Edelbrock part number 7576. Intake was installed on an engine and run for less than 10 hours. Intake has been sitting in the box since 2011. Some remnants of RTV and water scale remain as shown in pictures. Asking $275 +...

I have a set of Mopar cast aluminum valve covers, black crinkle coat finish. Mopar part number P5007611 Covers were installed on an engine but never run. Been sitting in the box since 2010. Includes reusable gaskets and baffles. Asking $125 + shipping from Fontana, CA (92336).

Selling a Hughes Engines Aluminum LA Engine roller rocker kit (part number HUG 15023). 1.5:1 arm ratio. I purchased this kit about 8 years ago from Hughes and installed it on a 360 I built but could not get to fire. Ended up going with a Magnum headed crate engine soon after and have had these...

I've been chasing a problem with my engine stalling in gear once it gets hot ever since I got it running, and I'm hoping someone here can point me in the right direction to possibly fix this thing. Engine is a 408 small block, 670cfm holley carb with a 1/2" phenolic spacer. Trans is a 727...

Hey guys, I need either some advice as to what to tackle with my brakes or a recommendation as to which shop in the Riverside/San Bernardino, California area to take my Duster to. I installed a rear disc conversion kit from Right Stuff Detailing (http://www.getdiscbrakes.com/) as well as new...

I just did some major brake work on my Duster, installed a rear disc conversion kit, all new lines, front calipers and rotors and new master cylinder all from Right Stuff Detailing. After stopping leaks and bleeding the brakes I can sit and pump the pedal with engine off and have a good firm...

I'm going to be pulling my axle shafts out in the near future to do a disc conversion on my car, and remember that pulling the axles out of my old 7&1/4 rear was a pain in the butt using the slide hammer. The axles I'm pulling are in an 8&3/4 housing, and have about 100 miles on the bearings, so...

Getting the last few parts together for my new engine. Magnum heads on a LA 360 block, stroked to 408ci. It's got the Edlebrock Air Gap intake on it for the Magnum, and I'm having a heck of a time finding a coolant bypass hose that will work with that intake and the LA water pump which looks...

Hey everyone, Been working on trying to get my 360 to start up for the first time all weekend and was unsuccessfull. Seems like the big problem now is that I'm not getting enough voltage to the coil. The instructions for my ignition kit (Mopar Small Block Electronic Ignition Conversion) say...

I'm working on a Slant 6/904 to 360/727 swap in my '73 Duster, and have all the appropriate linkages and brackets and such, save for one. I did not save the Torque Control Bracket from the 904 to use on the 727, however I do have one from a '70 challenger 727 that had column shift, that I think...

Hey everyone, I'm trying to figure out which carb to use on my engine, this is one of the last things I need to fire it up, and am kinda stuck. The engine is a 360, bored 0.030" over..giving a final displacement of 365CI. Cam is a Lunati Voodoo #60403 (advertised duration of 268/276, lift of...

Just got back from my local machine shop with my 360 block and crank..both are trash. block has already been bored .060 over, crank ground .030 and has had a crack welded, cast crank, welds are no good for those. and go figure, my measuring tools (calipers, micrometers) finally show up in the...

Hello everyone, I've been looking for a 360 around the Southern California area for about a month now, and have had a few deals and promises fall through. Couldn't find anything worth while at the local pick-a-parts, and looking on craigslist I've found a few, but no one I contact has been...

Hello everyone, I went down to the local pick-a-part this morning looking for a 360 and a 727 trans to swap into my '73 Duster. I found 5 of these combos in the yard, and was able to turn all the engines over by hand. I took a good hard look at one in particular, that looks like it's been...

So, I'm going over to a friend's place this week to take a look at a 360 she got as a backup to the 340 she's building into a 418 stroker for her Duster. I've never looked into buying a used engine before, and know absolutely nothing about Small Blocks. All I have ever dealt with so far is Big...

Hello everyone, new to the site. Actually found it through RumbleFish's Duster Project thread. I've got a '73 Duster that just lost a connecting rod and sustained some crank damage in its Slant 6. This is the second Slant I've gone through since acquiring the car almost 4 years ago. Coming soon...