Search results for query: *

Use a sawzall and cut out more than you need. You could take the door jambs and inner fenders also. Did you ask to buy the whole car? Also the amount of work you will put into the used quarters may not be worth it! I know the labour factor is free but you'll be sick of it by the time you get...

Each to His Own, But I like the B5 Blue.

No they are different.

Thanks Ted, never thought of welding it in from the backside. Good idea.

I have to patch a hole in a firewall. It is about 6" in diameter. Should I cut the patch the same size as the hole or should I have a 1/2" of overlap and crimp the edge all around? I think a patch of the same size would make a cleaner repair but may be a little harder to weld. Suggestions?

I have been doing plastic welding for years (mostly snowmobile stuff). As long as you work slowly, dont over heat the material and/or try to work to fast almost anything can be saved. It really depends how much time you want to put into it! :burnout:

Either your gas is not working or you are holding the tip to far from the metal. Do you have the ground on bare steel of the same piece of metal you are welding? The tip of the welder should be about 1-2" -3/4" away from the surface. Try using thicker material until you get used to the welder. I...

I finally found it!!!! its stamped on the drivers side right where the speaker would be. 1/2" from the front edge, and can be seen/read from the back window (I assume they stamped them before the window was but in & not when the sheet metal was made). There is double metal in this location...

The car has the factory fold down back seat.

I crawled in the trunk and looked all the way around, I would think if it was a punched number it would be on the backside,didnt really want to take off the seal. I'll go look again.

anybody with any info on this car please P.M me. I believe it is an Idaho Plate but I'm not sure.

Nothing there. i found 778D401 on the bottom center of the package tray, but that has no reference to the serial number at all, or any serial number for that matter.

that's my question. i have the dash, door sticker, fender tag and rad support. is there another # at the back of the car?

Ok, so I picked up the car. The number on the rad support is the same as the vin but I can't find the one at the back of the car. Anyone with a 1973 dart sport know the exact location?

Ya, that's what I,m hoping!

Heres one, are the 68' fenders the same as a 1973 Dart Sport? I'm thinkin of putting a 1968 hood/grill on the 1973 Dart Sport. I think as long as the hood fits everything else will fall in place. :burnout:

Please note that the first seven digits MUST be the same as mine. LM29H3B Thanks

Hello, I am looking for a photo to get a VIN decal made for the drivers door. Can someone please upload a photo of there factory decal FROM A 1973 DART SPORT 340. The decal supplier is asking for some axle weights with passengers? The only info I can find is...

Thanks, I also needed this. :burnout: Cheers

I know I don't have to enter the RIV program and there will be no costs involved. I just want to make sure i have my ducks in a row when I cross. the reason i ask it it is found in EXPLANATIONS ON MANDATORY COMPLIANCE found on the first three pages of...

Hello, I am looking at importing a US vehicle into Canada. Does anyone know where the USA compliance label is and/or have a picture? As per the RIV Vehicle import compatibility list - Explanations; 2. Admissible vehicles, except competition vehicles, snowmobile cutters and all terrain vehicles...

I understand there are 3 - 5 locations to correctly identify a car. I know of the following locations, 1) dash plate. 2) fender tag. 3) drivers door decal. I am flying from Canada to California to look at a car and I just want to make sure it is as advertised. I was told it is also stamped in...