Search results for query: *

Double tripled checked...it's actually 18-20ft-lbs. That is what I was going to do...until I dug out my Husky cheapo in-pd torque wrench. On the collar above the handle it has 16 markings, which made me think that there is 16in-pds to 1ft-pd...

I have a Snap On torque wrench for higher torque stuff. It is not the type where you crank the handle, it has a knob on the side with a dial that turns. Had Snap On guy that I know from the track check it, it is calibrated. But...and this is me just overcomplicating my life..changed the trans...

How about a gun bore light? https://www.amazon.com/dp/B07MMS7QXN/?tag=fabo03-20

No...but I will. Going to see my primary care doc for my monthly fix on Thursday, will take a look at his lights. Thank you Sirm, will look into it. Thanks Rob, will be looking at my docs ENT light Thursday. The sensor is 36mm×24mm, the chamber is only slightly larger so they are going to...

I read thru this thread Need a new flashlight None of the ones mentioned fit my needs. I need more of a pin point one. I need it peek around the sensor chamber of my cameras. I bought this one https://www.amazon.com/dp/B071WK4R76/?tag=fabo03-20 while it is fairly bright it is not bright...

What an absolute pain in the arse these things can be. Put 3 up in the bay I use for work. Had 0 troubles with them until I built my smoker under them. Now on all 3 of them the rear most bulb is out. Swapped bulbs, they worked. Seems like they need to be twisted to just the right spot to work...

Not all of us have a lathe so...

Not that the balance will be the same but the head has to flipped when mounting the LS on it, I think. Will check it when I go to lock the garage. Thanks Del...

Haven't you by chance rigged something up or was this just something that popped into your head? Thank you Sir. Just picked up the LS out of the wooden stand it was sitting on. My cherry picker is in the far end of my garage, 2 cars blocking access. Would have had to load it on my small trailer...

Anybody ever build a diy version of one of these things? Bit pricey but I don't see me safely spinning a motor over on one of the "manual labor" types anymore...

Just got done doing the annual maintenance on our two daily drivers. I ended up with one of them having the coolant start dripping overnight....it ended up missing the drain bucket so I have a bit of a mess. Mopped it up with some rags but the floor still feels damp...any suggestions?

Thank you. I have another clicker type torque wrench. The rotate the handle type..have never left it cranked up. Torqued a lug nut on my truck, Snap On one clicked as it was busting loose so it is probably pretty close. I will contact CDI about,sending it in, want to make sure. Thanks again...

CDI?

Holy crap...bought a used Snap On torque wrench off of FleaBay. It is,not the kind where you rotate the handle to set it, it has a knob on the side...anyway when I got it it was turned up to 175 ft.lbs. Stumbled onto a Snap On truck...he told me $75 to calibrate...plus shipping...Ouch...he did...

.....cleaned in an electrolysis tank? Replacing the injectors on my Duramax. The high pressure fuel lines have quite a bit of corrosion...have used the electrolysis tank for all sorts of cast iron...

https://www.amazon.com/gp/product/B005POGY74/?tag=joeychgo-20 ...from Napa the other day. My Duramax has a leak. Not a very consistent leak so it has managed to make a disaster under the truck. Anyhow...what to spray? Have acetone, odorless mineral spirits and a gallon of Brake clean in...

...it no work no more. Crawled under my truck, turned it one...flashed real bright and out it went. Have hated that LED pile-o-crap since day one. What are you folks using?

Some of the metal has some minor surface rust. Quick pass or two with a wheel on the angle grinder gets rid of it.

Attempting to straighten out the bomb drop zone...aka the garage. Hoping to get started on my smoker and bike projects soon. Pulled out and separated the pile metal. Have a whole pile of odd shaped pieces of plate. Want to cut them into chunks for practicing with the Tig some year. Any...

Mouse turd in the gelcoat....going to be pretty hard to miss THAT....Thanks for the tip...

The board in my ABS module apparently has some soldered joints that have failed. Was going to pull the module off and ship it to get repaired. Changed my mind. I have one of those clunky Weller guns...far from ideal for working on a circuit board. Any suggestions?

....arse...but the problem was indeed an open wire. Pulled new wires, hooked them up and we have water again...without the use of a generator

Got it.... Right now we have 2 services. A 200 amp on the hose and a 400 amp on the garage. Avatar, our power company, told us that the rates were going to be the same....the rates for the garage are 65% higher. Will be tying the house into the garage in the future. This one will have 3 90%...

We are thru the first 90* & 45*. Pretty sure we are thru the second 45*. Very slow going now. Have the pull string wrapped around a 4×4, one end of it laying in the tractor bucket while Ernie is lifting the other side. Give the wires a push...walk the 160' back to Ernie....roll the 4×4...

Splice a power supply?

....hate it. Will be pulling a trio of 2g with a single 4g thru 160' of 2" conduit....with 3 90* sweeps and a pair of 45* corners. Have lube.... problem is I am not a boy scout so my knot tying skills suck...

Hmmmm.....made more sense than putting it in the / or news and politics...

Made 4 round trips from Mesa Az to Spokane with no plate. Oddly enough on one of my trips I found my plate in one of the hotel parking lots I used. Never understood having a piece of plastic holding the plate half a foot off the pavement.

Car trailer plate in Montana is full size so any bike frame stuff won't work. I probably won't have any problems with the cops...unless I go thru Reardan with it...which is normally the route I go...the "Marshall" in Reardan is a real clown. 30mph is 30mph, not 30.01. He sits just inside where...

Sorry about the typo....auto correct on the phone and an operator not paying attention. What got trashed....bolts with LEDS in them...