Search results for query: *

Thanks. Found some close to me. Appreciate it.

Need lower control arms for a 74 Valiant with sway bar tabs. I know the early years are different. If you have them please PM me. Thanks, Larry

You talking about the big bottle thats on the passangers side of the radiator with a green top? If so I have one floating around here somewhere. PM me.

Auto parts store or hardware store. Push nuts. Don't look the same but will work, unless you are doing a 100 point resto.

Switch can be adjusted down to meet the pedal. I think its a 3/8 hex bolt on the passenger's side of the column support.

That is an easy fix for a decent welder. Weld in the worn area and grind it down to the proper diameter using the other hole as a guide.

If its a temp thing just use a bunch of 1/2 inch flat washers.

I can but cost is going to be around $25-30 each via UPS. The specs are: 2 each 15X8 with 4.65 inch back spacing 5 on 4.5 bolt pattern and 2 each 15X7 with 3.80 back spacing 5 on 4.5 bolt pattern. Have the center caps for all of them. Asking $200.00 for all 4 plus whatever it costs to ship...

Shame you aren't closer I have some Torque Thrust that I'd let go cheap (shown on my 69). Larry

PM me, I have the UCAs. Larry

Looking closer to home is at all possible but I'll keep you in mind if I don't find anything to my liking. Thanks. Larry

Sorry can't use the bulge hood. Would be a shame to cut it up for intale clearance. Wrong marker in a 67 fender. Appreciate it though. Larry

Hey Snake. How does that shelter hold up to the snow? I had one a couple of years ago that stretched out real bad when the snow began to pile up along the sides. Looks good. Car too... Larry

Tampa? I have a home in Ruskin, just south of there. Just don't get to see it much anymore. My sister has been living in it so long she thinks its hers. Wish she would take the mortgage.... PM me with some prices on what you have. I know shipping is going to be the killer but her insurance...

Think I can save the core support. It has a slight bow in the middle top where the hood latch place pushed it back but I "think" it will pull out. Where is Auburn, NY? My geography is lousy. Can place Buffalo, Albany, and most other large cities. What shape is the hood in? Asking Price? PM me...

Your bumper looks better than mine. Can you ship and what price? Thanks, Larry

How bad is it? The one I "had" was POR-15 with silver argent paint over it. Held up pretty well in the crash. Didn't even chip the paint on the bumper. Bent the He** out of it though!

I need a right front fender, hood, grille, bumper, and right side bumper brackets for a 69 Dart so I can fix the accident damage caused by a bimbo on a cell phone. As rust free as possible. Also may wind up needing a core support... Thanks. Larry

I got mine at Carquest but they are a little different. Nothing a bench grinder and file couldn't fix though...

Most of their stuff is made for early fords and chevies. You could probably make one work with alot of time and effort. If you have a sheet metal fab shop in your area they can bent up aluminum and mig it together so it fits into the dash. Here is a couple of pics of mine. Only thing is, I cut...

Measure your vent diameter. If its 2-1/2" then let me know. I have new stuff 4 ft piece (more than enough for 2 defroster vents) is $25.00 plus shipping. By drivers side under dash vent do you mean the one with the door on it? If so I may have one of those too. Larry

Does the 72 have the key in the column or on the dash? I have a 69 floor shift column thats partially disassembled but the tube, shaft, and housing for the TS switch is all there. Larry

Do you need the whole thing or just the parts to convert from column to floor shift? Larry

Do you want show quality or just something to cover up all the holes in the front? I have the 3 pc set but it has paint and scratches on it. If you are handy it can probably be made to look better than the chinese knockoff I have on mine. PM me your address, etc., and I'll send it to you. Larry

PM me. I may have one in my junk. Will have too look and see what condition its in. Larry

Here's the contact info for a guy in Milford, NH. He collects MOPAR parts and I've had real good luck getting rust free parts from him. He is a wealth of knowledge when it comes to interchange too. Gary LaPlante 199 Mont Vernon Rd (Rt 13) Milford, NH 03056 Phone 1-603-512-5481

Shame I'm not closer. I have a magnum 5.9 block and rotating assy I would give to you just to get room in my garage! Anyone in New England interest? Free to good home. Larry

I have a MP electronic ignition conversion kit (distributor, box, ballast resister, and cable) new in box. $75.00. PM me if you are interested. Larry

Make your own. In the end you have something that is the way you like it rather than what someone else thinks you should like. Larry