I have a Power Master 100 amp two groove pulley in chrome. Was on My car and I went to single wire Alternator. These sell for around 250 new on the "bay" $125 plus the ride. PREFER local pickup as shipping has gone from bad to terrible.
Also a stock 60 amp..this was on My car before I went to...
out of my 67 R/T...great running motor...78 block....rpm performer intake...newer aluminum waterpump and housing..452 heads with hardened seats..cast crank(thick balancer)...from sound and performance,a better than stock cam, heavier than stock valve springs(removed covers)Electronic distributor...
Pulled for a bucket list hemi. Good running 440...78 block...RPM performer intake...452 heads with hardened seats...aluminum waterpump and housing,electronic distributor. No idea of internals . Motor runs strong with a better than stock "sounding" cam and heavier valve springs(looked under valve...
1968 non HP 440 block,standard bore with end caps,oil pan,valve covers,push rods,rockers, and matching 906 heads. Selling for a friend. $500.00 for all. Will sell heads separate Located outside Buffalo NY
no idea of compression....I run 93 octane in all my cars as I never had one over 10 to 1 compression. It's a 78 block but my opinion it has been modified as it has good performance. I drove it 3 seasons and believe it's faster than a stock built 67 440hp motor.
The only reason for selling is I...
Pulled for a hemi replacement...excellent running 440 with 452 heads,rpm performer intake,electronic distributor. Have no idea of internals except heavier than stock valve springs(removed covers to look for wear). Motor has a nice lump to it and is pretty quick. 1978 block...runs on pump gas. If...
Removed from a my R/T after 3 seasons of service. Cleaned it up and painted. Had junk all over it on the bottom from a leaking power steering box. (Just added fluid for 2 seasons instead of fixing the power steering.) I know nothing of the internals except it has stock rockers and heavier than...
In excellent mechanical condition,just pulled from my 67 R/T..total rearend from drum to drum. 741 case...391 suregrip...works excellent..new green bearings last year...dirty and has grease from tranny leak spraying back...clean and bolt in and enjoy..no disappointments..11 inch breaks in very...
Just removed from My R/T for hemi swap. Excellent running 440 motor....intake to pan minus exhaust manifolds. 1978 Block with 452 heads. (hardened seats) Mild cam of unknown specs. Performer RPM intake,newer waterpump and housing. What you see is what you get. I bought the car 3 seasons ago and...
http://www.bigblockmopar.nl/tech/mopar-rearaxle-dimensions/
only goes to 66 A body
width of A body rearend...57 1/8 vs 59 1/2 for mine
flange 52 5/8 vs 54 1/4
perch 43 vs 44
mine id big bolt pattern
440 motor...just removed from my 67 R/T because of hemi build. Had for 3 seasons(came with car) and runs excellent. Have no idea of internals but from sound and performance the motor has been built. Intake to pan...no carb...or aternator and brackets brackets. Mid 70's block...452 heads...mild...
Just removed from my 67 R/T...complete rearend, drum to drum, 11 inch drums...391 suregrip..741 case..new green bearings...includes brake lines and e cables...just bolt in and enjoy....works perfect..no disappointments....removed for a dana....440 coming out for a hemi...so I'm...
Changed my B body from 8 3/4 to dana with caltracs and the shock mount plates are not needed. Very good condition. Located outside Buffalo NY. $100.00 for the pair
Brake drum to brakedrum....currently in my car but can deliver to Carlisle with advance non refundable deposit. 8 3/4 housing...I "think" it's a 489 case(can verify if serious) 391 gears, suregrip, new green bearings, works perfect..no disappointments...why selling ? I got a great deal on a...