Search results for query: *

#24 Byron :) Dover pole.................................... subject to change :rolleyes:

Kind of what it looks like

Hi, we have a 1970 Jensen Interceptor in our shop that needs some repairs and mods. These cars run a 440RB motor and 727 Trans package. The vehicle is currently running an aftermarket style twin 2.5” exhaust system off stock manifolds with mufflers and resonators and no crossover pipe. The...

Single picture ads :BangHead:

Looks fine from here :poke: :popcorn:

PM'd

A picture would help

I measured mine last week, it was almost .060 in the hole which would be in the ballpark of what your book says. My engine was made in mid or so of 1972, BUT, I do have stockish replacement .030 over pistons. Extra notes for everyone, All YOU OLD FARTS need to stop bickering about ****. People...

Here is my 74 duster with 71 valiant bumpers and 71 brackets. I put a 71 front end on as well. Kim

Maybe anyone can answer, but my question is I have a 73 Plymouth duster with a bench seat factory 4 speed. I've spent a lot of time trying to locate the factory shifter handle which I have. I was just wondering it seems like the shifter handle is close to the Steering wheel or the driver side...

Very cool!

@dartnabout :) 1969 Dodge D200 CAMPER SPECIAL | eBay

https://www.forabodiesonly.com/mopar/threads/console-tachometer-wiring-harness.554640/ post #7

Ditto. I have 15x4 and 15x8.5 centerlines on my 62 too. And two other sets of wheels and tires for it also. A set of street steelies, and some polished tt2's with slicks.

RIP @Tony Fields. His car goes to auction 1967 PLYMOUTH BARRACUDA VIN: BH29B72204041 COUPE

Thanks for the quick replies.It kind of feels like maybe the stickers were put on before the clear coat had dried.I'm not sure. I don't even know if that is possible.. But then again, it kind of feels just like build up around the old numbers.It's not a whole sticker but he said that is on there...

I should also mention that 2 of those relays and 2 of those fuses you see in the relay box are for the headlights. I didn't document any of that because it has been documented on FABO many times, but the voltage improvement to the headlights is almost unbelievable. Before the relays, with...

Here’s a tid bit from my wife. This lady always borrowed $20.00 from her b4 every pay day. Then she paid my wife back. The next time she borrowed again she didn’t pay her back then wanted to borrow another $20.00, the wife said no. The lady never asked to borrow again. The wife told me that it...

Really not that bad. I only owned a left side manifold, for quite a number of years, back in the old days, but never put it on a scale.

When did Chrysler install flat u-bolts? My original 62 8 3/4, 64 Sure-Grip (tapered axles and all), even my bb 4 speed 67 with torque boxes, none of them came with flat u-bolts. Recently swapped the rear out of my 64 with a later rearend that had regular u-bolts and 4:10s, changed the springs...

You're like a clay pigeon on a skeet range Karl. Be safe. Thanks for cruising by

Looking for Drum Brake Backing Plates 11x2.5 for 8.75". Must be useable, not super rusty PM me with anything you may have

That is so true. It has taken me so much longer than expected to get to this point, I might have gone a little crazy if it didn't work.

Thanks for that Steve. It brought tears to my eyes. Kim

Find one of these. Pep Boys maybe?? https://www.amazon.ca/Polishing-Remover-Repair-Universal-Stickers/dp/B09PHCG3C3?tag=fabo03-20 .

Maybe I miss understood this but I was told on here that none of the truck manifolds would fit the A body with a small block. But the 90's Dakota fit that's awesome

I do watch his videos sometimes, good honest info there. OP should check it out.

Sorry just seeing this, I’m going to be using a universal multi carb kit with a cable and I’ll probably have to make the bracket. I’d do $120 shipped to you up in the great white north if you want it. I don’t do PayPal anymore so it would have to be Money order, cashiers check or personal...

^^^ heavy!