Search results for query: *

The previous owner of my car added a go-wing to it. The deck lid will not stay open from the additional weight of the wing so I have to prop it up with a 2 x 4. I read an article somewhere at one time that the trunk lid torsion spring rods (if that's what they are called) need to be...

I took my 69 Dart apart so long ago I'm starting to forget how some parts are supposed to go back on. I have a new hood to radiator seal and can't remember which way it goes on. I think the open length-wise part of it faces forward but just want to double-check before I put it on. Am I correct?

I’ve been trying to find out what the correct diameter is for hood pin holes on a 70-72 Dart hood. Between here and a couple other forums I’ve read they are 5/8”, 3/4” and 7/8”. So which is correct?

Back in the fall I bought a hood with a dual snorkel scoop on it for my Dart that I was told by the seller was an original 72 Demon hood/scoop set-up. It was recently brought to my attention (as I was preparing to take it to have it painted) that it isn't an original set-up and is actually a...

I picked up a Demon hood for my Dart and the hood has factory hood pin holes in it. My Dart did not come with hood pins. I have an NOS hood pin kit but I'm not sure what body style it was meant for. The kit has 23" lanyards and I would like to know if that would be the correct length for my Dart...

I have an NOS dual snorkel scoop that I bought many years ago. Finally decided to use it and put it on my 70 Dart. I started to do mock-up and set the scoop on the hood to see how it would look before drilling any holes and discovered there is about a half inch of gap where the center forward...

I had my 69 Dart mini tubbed about 5 years ago. The project is going very slow but I am finally getting back to it. I ordered new brake and fuel lines for it a couple of years ago and upon trying to install the fuel line now I have found that the fuel line does not fit properly like the original...

Does anyone know of a way to clean/brighten up the finish of a hood latch by maybe soaking it in something that will strip the crud/corrosion off of it? I am not looking to have it replated or whatever it was that was done to them when new and I don't want to sandblast and/or paint it either...

Does anyone know if there is a supplier out there that sells the small, rectangular inserts that push into the headlight bucket mounts on a 69 Dart? They are the white plastic inserts that the screws for the headlight buckets screw into, three per side. I also need to get the round plastic parts...

I am going to be adding a set of belt moldings to my 69 Dart which didn't come with them originally. I could use some help regarding what the layout/spacing of the holes on the top of the doors and on top of the quarter panels along side the rear quarter glass should be. Also, I need to know...

I am going to be sending my 69 Dart GT to the body/paint shop soon and I have a question for other owner's of 69 GTs. I need to take off the body trim moldings and of course I don't want to damage or bend them taking them off. What I would like to know is for those of you who have taken your...

I need to repaint the black area on the trunk lid trim panel on my 69 Dart GT and would like a recommendation on what paint to get that is similar to the original factory black. I don't care about matching it exactly so I'm not looking for an expensive factory correct restoration type paint...

I'm putting together a list of parts to sell and I have this NOS emblem but don't know what it is for. It is a stick-on type. If anyone can tell me what it is for I would appreciate it.

Can someone tell me if the vent window frames on a 4 door 69 Dart are the same as on a 2 door hardtop?

I have a 70 Dart Swinger that I am getting close to finishing. I never noticed before but when I was going to put on the quarter panel and trunk Swinger emblems today I discovered that the emblems have only three pins on them. The passenger quarter and trunk lid have holes for four pins. The...