Search results for query: *

For sale is a brand new, still in the plastic and new box, Speedmaster 1-147-028 intake manifold. It has dual bolt pattern for both LA and magnum style. Brand new on Summit is like $226 right now, so how about $185 shipped in the lower 48. Located in Eugene, OR

Hi, I have a set of J Heads casting #3418915 and they decode to 1970-72 360. They have new hardened seats and stainless guides. I do not have any rocker shafts or rockers to go with them so BYOR. 2.02 intake, 1.6 exhaust. They had .008" shaved off the deck. Other than that, they are almost...

I have for sale a used Fitech FCC. I bought this in December of 2016, and have put lots of miles on it with no headaches to speak of. I just finally broke down and put an intank Walbro pump in my Barracuda. I do not have any of the AN fittings or fuel hose that came with the kit originally...

Hi, I have an unused, still in the box, X-pipe from TTi, part # XA25MP for 67-76 A-Body's. Located in Eugene, OR. New, these are $280 + shipping. I'm asking $225 + the ride. Thanks.

Hi, these upper control arms are from my 68 Barracuda, I switched them out for tubular control arms from firm feel quite awhile ago. They have really good looking bushings on them, I had replaced them with energy suspension bushings, and the ball joints are in good shape, Moog K7022's. I had...

Hello, I have a Lokar braided 727 kickdown cable kit. Everything is there. They go for $72.97 + $9.95 for shipping on Summit https://www.summitracing.com/parts/lok-kd-2727ht/overview/ so I was thinking $60 shipped in the lower 48 obo. Item located in Eugene Oregon.

Hey, I've got some slightly used Dynomax mufflers for sale 2 1/2 in/out. I only ran these for a short amount of time. I loved them, but for a daily driver, they were a little too loud, I went with the super turbos instead. They are in like new condition. They go for $70 a piece on Summit...

Hey, I've had this square back alternator sitting on my shelf for a while now. I ran it for just a little bit of time before switching it out for a bosch style higher amp one. The double groove pulley was removed because I had my March serpentine pulley on there. I think I have the double...

I believe this is a Milodon 16250 (M brand in pic), or a Mopar Performance P5249558, it is slightly used. I ran this on my 340 for just a little bit before getting a Flow Kooler brand. It is virtually new. Asking $45 shipped obo, located in Eugene OR

Hey, I have this wideband O2 controller and sensor that I got from 14point7.com a few years ago. It utilizes a Bosch O2 sensor like this one: https://www.amazon.com/dp/B000BZI4ZW/?tag=joeychgo-20 and has a gauge like this one: Solid Air Fuel Ratio Gauge and the controller and a length of wire...

So I have these 4 points style distributors, only 1 of them has the part # tag still on them. It is 3438422. I figured someone might want them for parts, it is hard to find advance springs anymore. $50 shipped obo. Located in Eugene OR

Summer cleaning continues and I found these in a box, figured someone could use them. They look an awful lot like these from Mancini Moroso Solid Steel Motor Mounts so I figured $25 shipped is a good deal. Item located in Eugene, OR Thanks for looking.

For sale is the driveshaft out of my 68 Barracuda. It measures 44-7/8" center to center of u-joints and has 7290 u-joints. It needs the rear u-joint but has the slip yoke for a 727 and a good 7290 u-joint on the front. I had a 8-3/4 in stock location and a 727 when I ran this. Had to change...

Hey, I've got a set of torsion bars taken off of my '68 Barracuda Formula S. They are the 892 and 893 bars. They are located in Eugene, Oregon and I'm asking $100 obo plus shipping. Thanks for looking.

Hey, I have a set of axles that I pulled out of my '68 Barracuda so I could throw in a set of 5x4.5 and run different wheels. These have good Green bearings on them. For some reason 1 of the axles is missing a single stud, but I would think that your local auto parts store has a replacement...

Hey, I have for sale a like new Quick Fuel carburetor. Here's a link to the Summit listing for all the particulars. http://www.summitracing.com/parts/qft-bd-680-vs It also comes with a Fragola 930002-BL Black Size (-6) x 7/8-20 Dual Inlet 4150 Fuel Line Kit, here's the Summit link for it...

Hi all, I have a Holley Street Avenger 670 VS for sale. It currently has 68 primary, 76 secondary jets. A 32 squirter, orange cam, and the black vacuum secondary spring. The Idle Feed Restrictor (IFR) has been drilled and tapped to accept 6-32 brass set screws and currently has a .031...

Hey, I've had this carb sitting on my shelf in the shop for years. Time to clear some stuff out. This is a 625 cfm with the Mopar linkage arm. It's going to need to swim in some carb cleaner for awhile and have a $25 rebuild kit thrown at it. It has the fuel line adapter so that the fuel...

Hey, I have a set of (4) aluminum wheel adapters that go from 4" to 4.5". I just used them for mock up with some wheels prior to switching over to 4.5" axles and rotors. Prior to me getting them, someone "clearanced" some off the back side of 3 of these for reasons unknown to me. I don't...

Hi, I have a complete set of 273 adjustable rockers, spacers, shafts, hold downs, and pushrods. I have 2 different sets of shafts, one with banana grooves that I cut, and one set of smooth shafts that I have from a stock set of stamped rockers. Buyer can choose which they would prefer, but...

Hey just thought I'd see if there was any interest here before I put this on eBay. I have a Howell K247B universal fuel injection kit for sale. It is used, but in perfect working condition. Came off of a Jeep that didn't see too many miles a year. I have 2 different chips for it as well...