Search results for query: *

Would like an 8.25" for my Duster to move it around while the current rear axle is getting sorted out. Let me know what you have, thanks. Gary

Looking for an over the counter Carter 750 AFB or Edelbrock AFB/AVS variant, mechanical choke preferred. I'm just going to machine off the choke provisions so the less to remove the better. Will consider a 750 CFM Street Demon for the right price. PM me with what you have Gary P.S. Not...

Looking for a FRONT 1973 Duster/Scamp bumper with brackets OR a Feather Duster front aluminum bumper reinforcement. I need to make my 1974 Duster lighter and I need to pitch the steel front bumper reinforcement or replace the bumper with a '73 bumper but would also need the '73 bumper...

Looking for a set of Doug's Headers D453 (small block 67-76 a-body) What ya got? Drop me a PM Gary

Looking for a 68-73 B-body in the New England area, closer to CT the better. Mostly looking for a driver, non-numbers matching is fine as are some mods. Price range is $5000 to $15,000 depending on the car condition and options. What ya got? Send me a PM. Gary

Looking for a 70's vintage 1 bbl for a 225, what ya got? Something working would be great. Gary

Looking for a junk flywheel to spin an engine over, anyone have one for sale? Will never have a clutch attached to it so surface is unimportant. Needs to be 8 bolt, fit a 10.5 bellhousing with 130 teeth.

1967 "DODGE" letters off hood. Front arm rest bases (color not important) Front hood trim perhaps (mine is funky) Visors, color not important (mine the stitches coming out) What ya got? Shipping to 06370 Keep an eye on this thread, will be posting more as I take the car apart.

Looking for a big block bellhousing, I'll let you know up front that if your price is anywhere remotely near $300 I'll just purchase a new unit from Brewers. Originality isn't an issue.

Looking for big bolt pattern rims with the backspace listed above, anyone have anything? Checked Summit and Jegs with no luck. Steel would be perfect. Gary

What ya got? Gary

Need a small u-joint driveshaft 49.5 inches center of joint to center of joint. LMK what ya got.

Looking for some uncracked 73-74 Duster tail light lens and a cheap single point type distributor for a small block. LMK what ya got.

Looking for roller cam for Magnum motor, and fuel pump extention. What ya got? My cam I was going to use turned out to be bad, might buy a regrind from Hughes or just run a stocker. Gary

Looking for the rubber insert or biscuit that hold up the tailpipe near the rear bumper on my 1974 Duster. I have the metal bracket but it looks like the rubber insert was ripped out. The rubber piece sort of looks like this- (see picture) The original had some 2 slots in it at the...

Looking for 340/360 "spool type" motor mounts. Front pipes for 340-360 A-body manifolds, 73-74. Drop me a PM please.

Looking for a drivers door panel black, Year One states 74-76 are the same but 73 is different for some reason. These are the regular panels, not deluxe, no woodgrain. LMK what ya got. Gary

Anyone have a LA series 360 10.5" flywheel for sale?

See the emblem in the picture, what ya got? I have a plymouth one if you want to trade. Gary

Need a set of cheap headers for a project, 1 7/8 is fine. What ya got?

Looking for the following parts for a 1967 Dodge Dart, I'll update this list time to time as required. Door handles (new) Drivers remote mirror (new) Passengers sunvisor Rear taillamps Bumpers (rechromed) Clutch pedal setup (got it!) Door panels (68 or 69 black) Rear seat skin (black)...

Looking for a 1967-1969 Dart hardtop for a driver, with a manual trans if possible. I tried the other day and was so annoyed after 24 hours I pulled the listing. Not looking for a car in a field or on a hill or in a junkyard, not looking for a Valiant, not looking for a Duster...

All set.

Just looking for a bare stock housing, unless you have a set of big bolt pattern axles too and I'll take them as well if the price is right. [email protected]

Need a rear housing, no axles, brakes or chuck required. Interested in axles only if they are big bolt pattern [email protected]

Drop me a line if you have any for sale. [email protected]

Need a 400 shortblock or a 400 block [email protected]

Looking for the front pipes from a Dart/Duster with factory 340/360 manifolds. Just the front 2-3 feet or so, already have new duals. I'm just trying to get a bit more exhaust flow for my 318 with the larger manifolds. Shoot me pics at [email protected]

Timing cover- 70's through 80's vintage for Magnum conversion, needs to have spot for fuel pump and timing mark. Dual plane or single plane Aluminum intake manifold- Looking for something fairly low profile, not interested in air gap style or Weiand units with no coil bracket...

Looking for roller cam for 5.9 Magnum Motor, one from 380hp crate engine would be great. [email protected]