[FOR SALE] 1.03 torsion bars with grease boots

-
Status
Not open for further replies.
Kern Dog

Kern Dog

Build your car to handle.
FABO Gold Member
Joined
May 23, 2010
Messages
13,584
Reaction score
39,891
Location
Granite Bay CA
Rating - 100%
24   0   0
Contact seller
I have a pair of A body 1.03 torsion bars and grease boots. They are USED but have been marked for L/R prior to removal. Unknown manufacturer but stamped in the ends are the numbers 35.8 and 1.03. $140/pair
Northern CA
Pay by PayPal

More pictures available upon request.
 

Attachments

Standard ride height or lowered? Were were the adjustors at ride height? I aon't want to lower my car any.
 
gliderider06 said:
Standard ride height or lowered? Were were the adjustors at ride height? I aon't want to lower my car any.
Click to expand...

I'm not sure I inderstand the question. These were in a 73 Dart that had a 440. The car had no engine when I got the car. The front end was up high since the weight of the engine and trans were not there anymore. The LCA adjusters were even with the bottoms of the control arms.
A better question might be "Are these T-Bars Indexed? This is where the hex at each end is different, allowing the car to sit the stock height without having the adjusters bottomed out or sticking below the LCA. In this case, I'd say that these are right for maintaining stock height with the extra weight of the 440 but may require backing out the screw a few turns if you have a small block.
 
Correct me if I wrong: IIRC, most all aftermarket 1.00"+ bars are not clocked/indexed.
 
pishta said:
Correct me if I wrong: IIRC, most all aftermarket 1.00"+ bars are not clocked/indexed.
Click to expand...

We went through that misunderstanding with PST's bars awhile back and they had new 1.03bars made with factory indexing, but never changed the info on thier website to reflect that fact.
The way to tell if the seller's bars are factory indexed is that the hex's on the ends are offset in relation to each other.
(both ends different if layed on a surface)

Unless I am mis seeing the OP's blown up and lightened, the are not factory indexed but zero clocked like the old PST ones were before they had the new ones made.

These are zero clocked (not factory indexing of the ends) and designed to lower the car.
Note how both ends of the bars are laying on a flat of the hex.
 

Attachments

I will have to check the indexing when I get back out to the shop today.
I have checked on shipping to as far away as Florida and ohio. It is $37-38 due to size and length. I've had offers as low as $100 shipped. Thanks, but if I dont get close to my asking price I'd rather keep them and use them myself later.
 
Didn't mean to mess up your sale Kern Dog, but hopefully that information will save you some headaches down the road.
 
Okay thanks. I've never priced them, I just recall how expensive the MP ones were.
These have been SOLD. Thanks, Greg
 
Status
Not open for further replies.
-

Similar threads

HotRod20
  • Locked
[SOLD] A body PST 1.03 Torsion Bars new never installed
Replies
13
Views
2K
HotRod20
HotRod20
David Dickerson
  • Locked
[FOR SALE] Small block torsion bars
Replies
0
Views
566
David Dickerson
David Dickerson
sgrip65
  • Locked
[FOR SALE] Early A Slant six Torsion Bars
Replies
2
Views
418
sgrip65
sgrip65
Thomas Davey
Which torsion bars are these?
Replies
12
Views
5K
Thomas Davey
Thomas Davey
D
  • Locked
[FOR SALE] torsion bars and shocks, as well as other stuff
Replies
0
Views
598
dusterbd13
D
Back
Top Bottom