[Found!] Wanted Mainshaft

Discussion in 'Cars and Mopar Parts Wanted' started by Jordan2840, Sep 12, 2017.

Thread Status:
Not open for further replies.
  1. Jordan2840

    Jordan2840 Member

    Messages:
    12
    Likes Received:
    0
    Joined:
    Feb 4, 2017
    Location:
    St. Louis, MO
    Local Time:
    4:16 AM
    Contact Seller
    Anyone know where I can find an A-833 mainshaft? 23-1/4" in length. 30 spline. I have miscellaneous parts I can trade or purchase outright. Thanks in advance
     
  2. rumblefish360

    rumblefish360 so close yet so far away

    Messages:
    28,385
    Likes Received:
    1908
    Joined:
    Jun 21, 2005
    Location:
    New York, on a Island
    View My Photos
    Local Time:
    5:16 AM
    Brewers I suspect
     
  3. Jordan2840

    Jordan2840 Member

    Messages:
    12
    Likes Received:
    0
    Joined:
    Feb 4, 2017
    Location:
    St. Louis, MO
    Local Time:
    4:16 AM
    I'm hoping I don't have to go that route. They want $370 for just the mainshaft
     
  4. hemi71x

    hemi71x FABO Gold Member FABO Gold Member

    Messages:
    3,328
    Likes Received:
    198
    Joined:
    Dec 22, 2009
    Location:
    Rancho Cordova, CA
    Local Time:
    2:16 AM
    Is 23 1/4 inch for an A body trans? Your ad really doesn't say.
    I have a mainshaft, but I'm pretty sure its out of a B & E body A-833 trans.
    Don't want to get it out of storage, as it's buried deep, if it's not what your looking for.
     
  5. Jordan2840

    Jordan2840 Member

    Messages:
    12
    Likes Received:
    0
    Joined:
    Feb 4, 2017
    Location:
    St. Louis, MO
    Local Time:
    4:16 AM
    I believe so. My transmission guy said I needed one with those measurements. With also 40 spline 1 & 2 hub and 40 spline 3 & 4 hub.
     
  6. hemi71x

    hemi71x FABO Gold Member FABO Gold Member

    Messages:
    3,328
    Likes Received:
    198
    Joined:
    Dec 22, 2009
    Location:
    Rancho Cordova, CA
    Local Time:
    2:16 AM
    Well then, what body style Mopar you guys working on anyway?
    Since this is an A body site, i would assume it's an A body car.
     
  7. inertia

    inertia Well-Known Member

    Messages:
    2,655
    Likes Received:
    124
    Joined:
    Feb 4, 2011
    Location:
    Victoria B.C. Canada
    View My Photos
    Local Time:
    2:16 AM
    23 1/4 inches is correct for A-body. cheers
     
  8. inertia

    inertia Well-Known Member

    Messages:
    2,655
    Likes Received:
    124
    Joined:
    Feb 4, 2011
    Location:
    Victoria B.C. Canada
    View My Photos
    Local Time:
    2:16 AM
    Depending on what is needed, consider a machine shop to repair yours. I recently had a worn input shaft bearing surface spray welded and machined for $160ish.
     
    • Like Like x 1
    Thread Status:
    Not open for further replies.