1966 Valiant Sheet Metal

-
Status
Not open for further replies.

The_night_rider

Sheriff of Rockridge
Joined
Sep 30, 2009
Messages
707
Reaction score
2
Location
Reno, Nevada
Rating - 0%
0   0   0
Contact seller
Good rust free lower rear quarters.

securedownload-21.jpg


securedownload-1-11.jpg


asking 150 for each rear quarter.


Hood- $100

securedownload-2-7.jpg



Can meet halfway for added gas cost fee.
 
Don't need full quarters - just wheel opening patch panels. How much to ship to 15089? Also in need of front and rear bumpers - straight cores or driver quality. PM me, I'm near Pittsburgh PA. I may be able to arrange to have a trucker friend pick them up.
 
I need this on both sides, can you get a picture of this area and under side ?
Shipped to 72401
 

Attachments

  • i16246.jpg
    83.6 KB · Views: 483
I need the lower trim that you show in the pictures of the quarter panels. let me know what you have and do you still have the hood. Are you going to spring fling if you are could you bring the hood.
 
here is what I need ...up to door handle would be good

http://i86.photobucket.com/albums/k117/scottylack/***.jpg
 
The lower trim in the rear quarters has only one piece. The other was taken off at some point before I got it.
 
Ok I'm going to go to where the car is stored next Saturday. I will take down the orders in which they came and go from there.
 
Still waiting to hear from you. If you cut from door to tail light about 4 inches above wheel opening it would be more than enough to replace what is bad on my 66 cuda. Still looking for bumpers- front and rear. PM or call 724-757-0893 (cell)
 
I would take the same but the passenger side but a little higher above the wheel well. cell 612-499-2187
 
I'm going down this coming saturday weather permitting, to where the car is stored. I will contact all you through PMs regarding which pieces you need. I will answer in order of who asked, don't worry, just give me a little time, things are pretty busy on my end, but don't worry. I hardly check this thread, the best way to reach me is to PM me. But whoever asked for which pieces in this thread will get them in that order. Fair is fair. Thank you for your patience.
 
Actually, send me pictures of your cars and where you need the metal. It works better than saying, just higher than that last spot.
 
The Cuda I need this metal for is between the wall and my 95 BMW M3, which I have to charge the battery to move, will do that Saturday and send photos.
 
I need this on both sides, can you get a picture of this area and under side ?
Shipped to 72401

I don't know how to post pictures in pm's :read2:
But this is the area's I need both sides if I fall in line to get them :happy10:
The green line is my bad area so I thought the red line is where it could be cut.
 

Attachments

  • i16246.jpg
    83.8 KB · Views: 394
Ok let me see what I can do about rear quarters, I might have a lead on more valiants for sheet metal if there is enough interest.
 
By all means look into the others as well. I need both sides, and the drivers side rocker from a 66 Valiant. Heres a couple pics of what I'm dealing with!!! Geof
 

Attachments

  • 100_2994.jpg
    72.4 KB · Views: 416
  • 100_2993.jpg
    100.8 KB · Views: 378
  • 100_2992.jpg
    69.2 KB · Views: 405
  • 100_2991.jpg
    71.2 KB · Views: 377
  • 100_2990.jpg
    95.5 KB · Views: 381
  • 100_2989.jpg
    80.3 KB · Views: 376
Ok. My inbox is full, so I'm putting it here, I have all of the parts and this weekend I will be tagging them and packing them up for shipping. I will contact everyone on payment arrangements and how to make them.
 
Thank you for the pm and keeping me in the loop :eek:ccasion:
All the way from Nevada to Arkansas shipping quote would be needed to 72401.
I wonder if this is doable, or it may be just a few extra $$ to get the hole 1/4 to me so I can cut it myself. Is the splash shield still attached behind the rear lower 1/4 ?
This will be a big investment that needs to be dun, I see your pm box is full so I hope this is not asking to much night rider.
 

Attachments

  • securedownload-1-11.jpg
    75.1 KB · Views: 305
I am looking forward to receiving a picture of the back side of the lower 1/4 and wheel well lip or a word from you that this area is good and solid metal :thumleft: has this been worked on in the past and has filler on it that you can see ? I CAN stand Some body work "dent reair":thumleft:
My son work's for
eng.ink.
5400 cw post road.
Jonesboro Arkansas
And it can be freighted there and save me some shipping
I will be here or you can e-mail me cost on getting it to me plus your asking price.

Thank you for your time and patients The_night_rider :color:
 

Attachments

  • Spring 2011 183.jpg
    64.3 KB · Views: 277
  • Spring 2011 184.jpg
    56.5 KB · Views: 274
I can get you pics of that no sweat, that is from the year it was down in ca. It sat in the shade and was rained on, no rot, but I will get you pics.
 
Status
Not open for further replies.
-
Back
Top