Indianapolis, In trade show and swap meet

-

Flyinbrian72duster

Dart and duster
Joined
Jul 15, 2017
Messages
215
Reaction score
63
Location
Cedar lake in
24th Anniversary Chrysler Performance Trade Show & Parts Swap Meet. Saturday March 2nd 9 a.m.to 5 p.m.sun March 3rd 9 a.m.to 3 p.m. Indiana State Fairgrounds 1202 E. 38th st., Indianapolis, IN 46205 Any one going? Selling stuff?
 
24th Anniversary Chrysler Performance Trade Show & Parts Swap Meet. Saturday March 2nd 9 a.m.to 5 p.m.sun March 3rd 9 a.m.to 3 p.m. Indiana State Fairgrounds 1202 E. 38th st., Indianapolis, IN 46205 Any one going? Selling stuff?
I'll be there on Saturday! Looking for LD-340!
 
I'll also be there Saturday to look for six pack carburetors and '69 Coronet front fenders.
 
Right on ! Still not sure if I'm going sat or sun I heard sun sucks
I've never been to it before. But from experience with swap meets, you can get better deals on Sunday, but the sellers are losing interest and packing up to leave. I'm going Saturday while its still fresh.
 
I've never been to it before. But from experience with swap meets, you can get better deals on Sunday, but the sellers are losing interest and packing up to leave. I'm going Saturday while its still fresh.
I whent last year sat it was good I'm aiming for sat again
 
I will be there in the front hall along the right wall when you come in with tons of A-Body parts. I'm the Dart guy, and Casey next to me is the Barracuda guy. I will have a neon green long sleeve shirt, can't miss my fat ***...
 
I'll be attending along with fellow members of Tri-State Mopar Club. We attend every year.

I always enjoy this event. It reminds me that spring is just around the corner. Plus there are usually some good deals there.

In previous years, it was always great to visit with FABO member Tony Fields. RIP Tony.
 
Last edited:
We will be located in the second building against the right hand wall. Large selection of Top Catwhiskers and other weatherstripping products along with washer bottles, battery cables and all of the other restoration products and materials.
 
24th Anniversary Chrysler Performance Trade Show & Parts Swap Meet. Saturday March 2nd 9 a.m.to 5 p.m.sun March 3rd 9 a.m.to 3 p.m. Indiana State Fairgrounds 1202 E. 38th st., Indianapolis, IN 46205 Any one going? Selling stuff?

I’ll be there I’m bringing a lot of my 72 Dart parts. Hit me up if you’re there and need anything...

Here is a list of parts for a 72 Dart I will have there with me.

I am leaving the 72 Dart seats at home, however I am only about 40 minutes or so from the fairgrounds...

72 Dart

Rust free doors all glass intact $250 each
Side windows rear $100 pair
Dual horns $50
Windshield trim $150
Rear Window trim $50 sides/top only bottom parts missing
Rear bumper with brackets $125
Taillight housings left and right with lenses $100
Quarter panel extensions left and right
Hood chrome $100
Dart emblem $15
Gas cap $30
Dash wiring $150
Engine wiring $100 needs some work (I may fix it)
Tailight wiring $100
Armrest bases and armrests with ashtrays (rear)$50 pair
Kick panels $45
Trunk latch both parts $35
Driver side Spindle $75
Driver and Passenger side 9” drums, shoes, bearings brake parts $250 (New)
Remote mirror $50
Heater box $75
Hubcaps $40 set of 4
Dome light with wiring $45
Under front seat seatbelt wiring $30
Door jamb/rear window rubber pair $30
Inner door chrome trim and rubber $150 both sides
Interior headliner door trim pieces $80 both
Seat belts $75
Window cranks $20
Backseat cardboard divider $45

Prices are definitely negotiable, I’d really like to not bring any of it home.
 
Today’s meet was smaller than the last time I went but still lots of good deals.
 
You got that right. That's 5 hours I'll never get back.
Oh it couldn’t have been that bad. Then again, anytime I’m at any Mopar event, it’s never a bad time.
 
I went looking for a used aluminum 340 intake.
Found one LD-340 that looked pretty ratty for 450.
Found a Torker 340 that wasn't in too bad shape, except one carb mounting hole was tapped out to 5/16" and the kid selling it was firm on the 140 he was asking for it.
And found one Torker ll 340, possibly the worst small block intake ever made by edelbrock.
That's it except for high rise and tunnel rams.
Couldn't even buy a new performer rpm there today.
I did pick up a new driver's side mirror for 59$ though. That was the highlight for me.
 
Oh it couldn’t have been that bad. Then again, anytime I’m at any Mopar event, it’s never a bad time.
You're right, it didn't completely suck. It just mostly sucked. I do like looking at old car parts, but I would've stayed home and ordered the mirror I got if I'd known there would be any manifolds to buy.
 
I went looking for a used aluminum 340 intake.
Found one LD-340 that looked pretty ratty for 450.
Found a Torker 340 that wasn't in too bad shape, except one carb mounting hole was tapped out to 5/16" and the kid selling it was firm on the 140 he was asking for it.
And found one Torker ll 340, possibly the worst small block intake ever made by edelbrock.
That's it except for high rise and tunnel rams.
Couldn't even buy a new performer rpm there today.
I did pick up a new driver's side mirror for 59$ though. That was the highlight for me.
Last time I went, summit racing had a semi load set up. I didn’t see them today either
 
I did ok. Got some 1.6 rockers from Mancini. Some marker lights for my 71 dart and picked up some stuff from Van's auto.
 
-
Back
Top