Stop in for a cup of coffee

-
djE.gif
 
All caught up, how is everyone doing?? Have to work on the brakes on my car trailer, might need new stuff......Has a handle you engage to keep wheels from rolling when tilting the deck, it sticks.....PITA to get released....
 
Last edited:
Running around doing a hundred different things. Now i have to hunt up a gallon of gas, think i will run out before i get to town. Got darker red for the fargo, that is pretty much what i want. Picked up cab with forklift and carried it outside. Next i will be driving chassis over to pressure washer, so i can clean it and prep for paint. Who am i kidding, im going to blow the loose dirt off and slap a coat of black on it.
 
I know it is not a popular position but I love fender flares on anything! I was seriously torn on putting them on the Demon. In the end I chickened out and did not.
my dart "May" get some subtle ones, haven't decided yet either. Really don't need them on the back with the rims I have, and the front is already wider. i have a spare set of 73-76 fenders I thought I'd try it on first, then swap back if i didn't like them
 
All caught up, how is everyone doing?? Have to work on the brakes on my car trailer, might need new stuff......Has a handle you engage to keep wheels from rolling when tilting the deck, it sticks.....PITA to get released....
here.
 
Good Morning Gang. Got an old rusty Toyota Tacoma here with brake lines leaking....Oh the drama...Oh the Fun.....
Ohhh. And now I see the break is in the worst possible spot....Sh** is rusted bad also...Gonna be a Bi***...to repair
 
I Wish...In fact I wish I hadn't taken this job........Must go buy BEER....
I ever tell you the time I was putting air bags on my Brand new toyota 4 runner? I was running wires for the compressor, and decided to drill a hole in the rubber gromit holding the main wire loom . Well the drill slipped and tore the heck out of the wires, right at the firewall. On a brand new, week old Vehicle. I had to completely remove the harness from the vehicle to repair it. What a job!!! Learned a lesson there....
 
my dart "May" get some subtle ones, haven't decided yet either. Really don't need them on the back with the rims I have, and the front is already wider. i have a spare set of 73-76 fenders I thought I'd try it on first, then swap back if i didn't like them


I like the shape of the fender opening on the front of the Swinger and would like the rear to match. That half fender skirt look just don't make it with me.
 
OMG I Cannot believe how STUP{ID half of Americans have become!!!!!!!!!!!!!!!!!!!!!!!!!! :BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead::BangHead:
 
Time is flyin today. Have to shut down and put stuff away,lock up and go to a friend’s place for dinner. Fargo chassis need a little time for water to evaporate anyway. Just warshed it.
 
Score for me!! The parts I bought from my buddy with the 67 Barracuda included some dented twisted trim all taped together. I didn't really look to closely at it since I was giving it to John. He asked for some pics this morning, so I went out and pulled the tape off to take some pics. Low and behold there on a piece of trunk trim was the two end molding clips I've been searching for. In addition, a nice complete set of trim molding pieces with the correct trim nuts. It was a one year only clip. They make some close, but not like it. I'm smiling today!!
Awesome!
I'm just glad you are not smiling holding the wrong nuts. :rolleyes:

Goood Morning!
 
Time is flyin today. Have to shut down and put stuff away,lock up and go to a friend’s place for dinner. Fargo chassis need a little time for water to evaporate anyway. Just warshed it.

There are very few words to describe how badass that video is.
 
Last edited:
-
Back
Top