Skunkwürks quarantine 4.0 build

-
Heywodja

Heywodja

The Heartbeat Stops Here
FABO Gold Member
Joined
Aug 16, 2014
Messages
1,524
Reaction score
1,328
Location
Texas
9A6269DC-3E1E-45F8-A0E4-2DD024268261.jpeg
251BFEEA-9BF6-465E-BFC4-B57A9A5B3C5C.jpeg
And so it begins...
 
nice, my 408 has a 4 inch stroke
your gonna love the torque
 
Here I was hoping for a Jeep build
Only thing better than a 4.0 would be a 4.25
what's the delta in cost?
 
Molnar crank & rods / balanced rotating assembly
Trickflow heads

more to come
 
Rods bearings are in, block has been rough honed and align honed.
rods.jpg


Block.jpg
 
Last edited:
New Molnar Crank, next step is to mock up to to determine how much the deck needs to be milled if any...
upload_2020-4-29_15-57-50.jpeg
 
Block has been align honed, decked, bores honed and final honed with torque plates, oiling mods done and is ready for mock up and clearance checking. Few more goodies roller timing chain, oil pan, cam & lifters, bearings and heads...
0821200853_resized.jpg
0821200855_resized.jpg
0821200856a_resized.jpg
0821200858_resized.jpg
0821200903_resized.jpg
0821200859_resized.jpg
 
make sure you inspect that oilpan
milodon does not have a reputation for quality welds (something they blame on the EPA and their inability to test welds with oil)
 
Those windage studs are $61 for 4? Yikes, I can imagine how much money you got in this build already! Ill watch this build as Ill never be able to afford it. :thumbsup:
 
pishta said:
Those windage studs are $61 for 4? Yikes, I can imagine how much money you got in this build already! Ill watch this build as Ill never be able to afford it. :thumbsup:
Click to expand...


And finding those damn studs are near impossible. I now have 2 sets because Summit can’t follow simple directions.
 
yellow rose said:
And finding those damn studs are near impossible. I now have 2 sets because Summit can’t follow simple directions.
Click to expand...

Reminds me of a big 7 blade alum. fan I bought from jegs a long time ago , they kept sending me steel bladed fans , after 3 of them , I cancelled the order and asked for a shipping retun # , sent all three back and got my $$ back.
 
nice i have the same crank and rods in my 426 , what are the specs on the pistons ?
 
Nat said:
nice i have the same crank and rods in my 426 , what are the specs on the pistons ?
Click to expand...


Dish -28cc, 487 Grams Advertised Weight

Pistons.JPG
 
Last edited:
This is a sea level car street car, we are shooting for just under 10.0.
 
Heywodja said:
This is a sea level car street car, we are shooting for just under 10.0.
Click to expand...

I like what you are doing there, I am working on similar build, you are ahead of me so I can get some pointers from you. Is that Howards a shelf cam or custom grind ?
 
It is a custom grind cam, and honestly I am not sure what grind the builder ordered we were talking about it Friday when it arrived at his shop, so I have yet to get all the specs hopefully in the next few days I will have the specs and I will share them when I get them.
 
Heywodja said:
It is a custom grind cam, and honestly I am not sure what grind the builder ordered we were talking about it Friday when it arrived at his shop, so I have yet to get all the specs hopefully in the next few days I will have the specs and I will share them when I get them.
Click to expand...
one thing for sure you are using quality parts , should be a nice engine, wish i had gone with the Mahle pistons . Much lighter than the DSS pistons i'm using
 
You must log in or register to reply here.
-

Back
Top