426 Hemi into a 67 68 or 9 Notchback Cuda

-
mopp_0804_cuda_06_z-69_hemi_cuda_convertible-.jpg
mopp_0804_cuda_09_z-69_hemi_cuda_convertible-.jpg?fit=around%7C770:481.jpg
mopp_0804_cuda_02_z-69_hemi_cuda_convertible-.jpg?fit=around%7C770:481.jpg
mopp_0804_cuda_03_z-69_hemi_cuda_convertible-.jpg?fit=around%7C770:481.jpg
mopp_0804_cuda_10_z-69_hemi_cuda_convertible-.jpg?fit=around%7C770:481.jpg
mopp_0804_cuda_05_z-69_hemi_cuda_convertible-.jpg?fit=around%7C770:481.jpg
 
Fast Facts
'69 Plymouth Hemi 'Cuda convertible
Tom Skjonsberg, Red Deer, Alberta, Canada
Restored by Joey's Place, Edmonton, Alberta

Mopar Power

Engine:The one you couldn't get as a factory option in a Barracuda '69---the 426 Hemi. Sourced from a '68 Hurst Hemi Dart, then treated to an original-parts rebuild--starting with a .030-inch overbore--by Lee's Brothers Hi Performance Racing Engines, Red Deer, Alberta.


Transmission: A-833, with a non-console-stick Hurst shifter.

RearEnd: A Dana 60 that didn't have to be narrowed because it came out of the same Hemi Dart that the engine and transmission did. It's got 35-spline Strange axles, 4.10 cogs, and a limited-slip differential.

Sure Grip

Suspension: Restored front torsion bar/rear leaf spring.

Brakes: Wilwood disc brakes in front, 11-inch Mopar drums in back. No power assist because there's no room for a power brake booster in the Hemi-stuffed engine bay.

Wheels:15x61/2-inch steelies with correct '69 Plymouth dog-dish caps.

Tires: repro 205/70R15 redlines all around.

High Impact

Body:Original '69 Barracuda convertible body restored by Joey's Place, Edmonton, Alberta. Rear quarters, floorpans, trunk floor, and front fenders were replaced (all but front fenders are repro); a Hemi K-member from a donor '68 Hemi Dart was installed; paint is black basecoat/clearcoat); and stripes, hoodscoops, and the rear luggage rack were installed by Joey's Place. Parts not supplied by YearOne came from three parts cars.

Interior: Original white bucket seat interior was restored using YearOne repro seat kit and other supplies by Joey's Place, Edmonton, Alberta. Sound system is OEM Mopar AM radio with centre-dash speaker, augmented by a 3-inch exhaust system behind the Hemi.


Top: New top and mechanical parts sourced from YearOne and installed by Joey's Place, Edmonton, Alberta.
 
Fast Facts
'69 Plymouth Hemi 'Cuda convertible
Tom Skjonsberg, Red Deer, Alberta, Canada
Restored by Joey's Place, Edmonton, Alberta

Mopar Power

Engine:The one you couldn't get as a factory option in a Barracuda '69---the 426 Hemi. Sourced from a '68 Hurst Hemi Dart, then treated to an original-parts rebuild--starting with a .030-inch overbore--by Lee's Brothers Hi Performance Racing Engines, Red Deer, Alberta.


Transmission: A-833, with a non-console-stick Hurst shifter.

RearEnd: A Dana 60 that didn't have to be narrowed because it came out of the same Hemi Dart that the engine and transmission did. It's got 35-spline Strange axles, 4.10 cogs, and a limited-slip differential.

Sure Grip

Suspension: Restored front torsion bar/rear leaf spring.

Brakes: Wilwood disc brakes in front, 11-inch Mopar drums in back. No power assist because there's no room for a power brake booster in the Hemi-stuffed engine bay.

Wheels:15x61/2-inch steelies with correct '69 Plymouth dog-dish caps.

Tires: repro 205/70R15 redlines all around.

High Impact

Body:Original '69 Barracuda convertible body restored by Joey's Place, Edmonton, Alberta. Rear quarters, floorpans, trunk floor, and front fenders were replaced (all but front fenders are repro); a Hemi K-member from a donor '68 Hemi Dart was installed; paint is black basecoat/clearcoat); and stripes, hoodscoops, and the rear luggage rack were installed by Joey's Place. Parts not supplied by YearOne came from three parts cars.

Interior: Original white bucket seat interior was restored using YearOne repro seat kit and other supplies by Joey's Place, Edmonton, Alberta. Sound system is OEM Mopar AM radio with centre-dash speaker, augmented by a 3-inch exhaust system behind the Hemi.


Top: New top and mechanical parts sourced from YearOne and installed by Joey's Place, Edmonton, Alberta.
Restored?! Nice but still made up like the OP wants. Also the big block K frame won’t work with a Hemi, someone might make one but..
 
This 67 convertible has been at Carlisle the last 2 years I've been there. Cross ram Hemi and a 4 speed Really nice car that is DRIVEN not trailered. Much respect to the owner

IMG_4186.JPG


IMG_4187.JPG


IMG_4188.JPG
 
"Give a man a fish, and he eats for a day. Teach a man to fish, and he will sit in a boat and drink beer all day."
Give a man fire, and he's warm for a day. Set a man on fire, and he's warm for the rest of his life :p

OP, as others have pointed out, this will be an expensive and time-consuming project - but only you can decide if the eventual rewards are worth it.
Previous experience stuffing big-blocks into A-bodies definitely comes in handy. It's a lot easier to get info and help than when I did my first 383 Valiant in 1983. No Internet back then, and not much aftermarket support either (except the Direct Connection catalog and Engine/Chassis books) :rolleyes:
 
Notch and fastback sit on same platform-frame

…and the exact same engine compartment as a Dart.

Go look in the Hemi super stock forum. Lots of pictures and descriptions of how to and what’s needed.
 
Last edited:
Only as difficult as you want to make it. I went the motor plate route. Hooker headers and a hammer. Also using offset master cylinder.
I’m back on the project after building my garage and a few setbacks.

02E69CB1-CBD2-45FE-A935-FD9D77628CF8.jpeg
 
Fast Facts
'69 Plymouth Hemi 'Cuda convertible
Tom Skjonsberg, Red Deer, Alberta, Canada
Restored by Joey's Place, Edmonton, Alberta

Mopar Power

Engine:The one you couldn't get as a factory option in a Barracuda '69---the 426 Hemi. Sourced from a '68 Hurst Hemi Dart, then treated to an original-parts rebuild--starting with a .030-inch overbore--by Lee's Brothers Hi Performance Racing Engines, Red Deer, Alberta.


Transmission: A-833, with a non-console-stick Hurst shifter.

RearEnd: A Dana 60 that didn't have to be narrowed because it came out of the same Hemi Dart that the engine and transmission did. It's got 35-spline Strange axles, 4.10 cogs, and a limited-slip differential.

Sure Grip

Suspension: Restored front torsion bar/rear leaf spring.

Brakes: Wilwood disc brakes in front, 11-inch Mopar drums in back. No power assist because there's no room for a power brake booster in the Hemi-stuffed engine bay.

Wheels:15x61/2-inch steelies with correct '69 Plymouth dog-dish caps.

Tires: repro 205/70R15 redlines all around.

High Impact

Body:Original '69 Barracuda convertible body restored by Joey's Place, Edmonton, Alberta. Rear quarters, floorpans, trunk floor, and front fenders were replaced (all but front fenders are repro); a Hemi K-member from a donor '68 Hemi Dart was installed; paint is black basecoat/clearcoat); and stripes, hoodscoops, and the rear luggage rack were installed by Joey's Place. Parts not supplied by YearOne came from three parts cars.

Interior: Original white bucket seat interior was restored using YearOne repro seat kit and other supplies by Joey's Place, Edmonton, Alberta. Sound system is OEM Mopar AM radio with centre-dash speaker, augmented by a 3-inch exhaust system behind the Hemi.


Top: New top and mechanical parts sourced from YearOne and installed by Joey's Place, Edmonton, Alberta.

sounds like a check writer , did nothing himself ----------
 
OP, if you pursue this project and you need help, let me know and I will try and help you out.
 
My whole life I've wanted a Hemi car doesn't matter if it's "real" or not (My *** won't know the difference!!!) The 68 Barracuda I bought last year made me crazy when I bought it because it's SO FREAKIN COOL!!! All I thought it needed was a Hemi. Then I realized that the 340 in it runs really good , it fits in the engine compartment , and I can work on it myself. In the end I decided just to improve the steering , braking , handling and leave the 340 in it.

IMG_4375.JPG
 
My whole life I've wanted a Hemi car doesn't matter if it's "real" or not (My *** won't know the difference!!!) The 68 Barracuda I bought last year made me crazy when I bought it because it's SO FREAKIN COOL!!! All I thought it needed was a Hemi. Then I realized that the 340 in it runs really good , it fits in the engine compartment , and I can work on it myself. In the end I decided just to improve the steering , braking , handling and leave the 340 in it.

View attachment 1715780549


Having owned and driven both, I tend to agree. My Hemi Cuda is a brute in acceleration, but lacks handling. These cars are not for everyone. The 340 in a well sorted out chassis is a much better balanced performer. It won't outrun an elephant, but it's more fun to drive.
 
My whole life I've wanted a Hemi car doesn't matter if it's "real" or not (My *** won't know the difference!!!) The 68 Barracuda I bought last year made me crazy when I bought it because it's SO FREAKIN COOL!!! All I thought it needed was a Hemi. Then I realized that the 340 in it runs really good , it fits in the engine compartment , and I can work on it myself. In the end I decided just to improve the steering , braking , handling and leave the 340 in it.

View attachment 1715780549
Very nice car you have there!
 
And his loss, but who would have known back then.
This car was featured in I believe 2008 Motor Trend Magazine or Hot Rod Magazine years after the Dart probably met an early demise. The motor and drive train don't have a shelf life. Having it in his possesion by no means is a loss of any type.
 
I have "put my touch" on this car and I can't wait to get it running again. What started as a simple "fix the oil leaks and detail" has snow balled into a $15,000 project!!! No stone left unturned LOL I have torn down and rebuilt this car myself in the backyard garage. The only work I'm going to farm out is the headliner and front end alignment No One will spend the time and effort to build it the way I want (I couldn't afford the ones who would) In the end when someone says "Nice car man" it will really mean something to me


IMG_1259.JPG


IMG_1254.JPG


IMG_1250.JPG
 
Last edited:
-
Back
Top