Recent content by airgrabber

  1. A

    73 duster brake question

    The issue with vacuum is more to do with how much you have at idle, and at cruise, not so much with accessories using some of the vacuum. Bigger cams affect the amount of vacuum the engine will make. Stock motors with stock cams typically make between 15" to 19" of vacuum, and brake boosters are...
  2. A

    [FOR SALE] Drag Car 73 A body UCA BB pattern w/Adj Bump Stops

    This is a pair of 73 A body big bolt pattern upper control arms, modified for drag racing by adding adjustable bump stops. Useful when tuning a car leaving the starting line, to limit front end travel. Ball joints and control arm bushings still have some life left to them, no slop in ball...
  3. A

    [SOLD] 2 sets MP Chrome Big Block Valve Covers

    First off, these are NOT show quality, but would be ok for a daily driver. These are used. There are some typical rust spots from use, one corner of one cover has some chrome peeled off - see pics. Set 1 is pics A - E, set 2 - pics F - I. With a good cleaning and a little steel wool these will...
  4. A

    [SOLD] 383/400 Holley Street Dominator & Electronic Distributor

    Update - small chip in one of the bolt hole mounting areas near the coil mount, visible in 1st intake pic above, should not affect installation or sealing, no cracks, no stripped or helicoiled threads, close ups attached.
  5. A

    [SOLD] 383/400 Holley Street Dominator & Electronic Distributor

    Factory 383/400 electronic distributor, stamped rebuilt by a Distributor rebuilder, plus low deck Holley Street Dominator intake manifold. Cleaned, bead blasted but sitting for a while, dust off, paint and go. $200 for BOTH, plus shipping and paypal fees. Pm with your zip code for total shipped.
  6. A

    [FOR SALE] 14" Hub Caps/Wheel Covers - 2 sets - $75 each set or $100 2 sets

    1st set w/Spinners sold, 2nd Set / Plymouth still available.
  7. A

    [FOR SALE] 14" Hub Caps/Wheel Covers - 2 sets - $75 each set or $100 2 sets

    I have 2 sets of 14" wheel covers - WYSIWYG, one set Plymouth, 1 set Dodge. Part number on the Plymouth set is 2823010, no pn on the Dodge set. Each set of 4 is $75, or $100 for BOTH sets, plus shipping and paypal fees.
  8. A

    [SOLD] NOS DC Small Block LA Valve Covers

    NOS, never installed, in original condition, in original packaging, with factory chrome bolts and grommets. Box is from late 80's, early 90's, has some shelfware but covers have been kept in original plastic/paper wrap within the box, hardware kit factory sealed. $75 plus shipping from Florida...
  9. A

    [SOLD] A body disc brake prop valve - $60 shipped in the USA

    It's a junkyard find.
  10. A

    [SOLD] 4500/4150 adapter

    It's threaded on the dominator side, not on the 4150 side. So to put a 4500 on a 4150 manifold. But I'd bet you could drill out the threads and go the other way...it's 2" tall
  11. A

    [SOLD] Aerospace Components Caliper Bkts - 73 A Disc Spindles

    WYSIWYG - $40 for the pair shipped in the USA< USPS Money Order or Paypal + 4%
  12. A

    [SOLD] BB Headers - Hedman Ceramic Coated B/E Body

    Ceramic coated, installed and clearanced in a couple places but never fired or run, some surface rust / shelf ware. 2" tube OD, collector length from slip tubes to flange stop 12", collector diameter 3". More pics available. $450 plus shipping from Florida, USPS Money order or paypal + 4%.
  13. A

    [SOLD] 4500/4150 adapter

    WYSIWYG - $30 plus shipping from Florida, USPS Money Order or Paypal + 4%.
  14. A

    [SOLD] Holley Street Dominator - 383/400 Low Deck - $200 + Shipping

    WYSIWYG - cleaned, bead blasted, $200 plus shipping from Florida. USPS Money Order or Paypal +4%.
  15. A

    [SOLD] A body disc brake prop valve - $60 shipped in the USA

    WYSIWYG...$60 shipped in USA, USPS Money Order or Paypal + 4%
See more
Back
Top