Recent content by Alan J Odze

  1. Alan J Odze

    NEED AN INSPECTOR

    I was wondering if anyone knows of an inspector located in Russell Kansa to inspect a MOPAR? Thank you Al
  2. Alan J Odze

    Shops or people that work on A Body's near Eastern PA

    Call Jamie Passon at 570-401-8949. He is in White Haven. I am sure he can recommend someone. Great guy.
  3. Alan J Odze

    Metal Building/ Garage…

    I have a 30x45x18 building. I was talked into a 22x12 single door. I hate the single door and would never recommend one. You are better off with two doors and a man door.
  4. Alan J Odze

    Fab room ceiling height?

    Those lifts are not overheat. They are chain or cable guided with a floor plate. Try removing a tranny with a floor plate. And the unground lifts are very expensive. 14 feet is the lowest to go with a twin post lift.
  5. Alan J Odze

    Fab room ceiling height?

    if you want to ever install a lift minimum height must be 14. I have 20 foot ceiling with one lift. My lift is 12 foot.
  6. Alan J Odze

    [SOLD] BRAND NEW A833 SHIFTER KIT COMPLETE

    I am not sure how to measure that. Dan at Brewers put this shifter together for me. Maybe you can ask Dan. It is for an A BODY a833 tranny. Thank u Al
  7. Alan J Odze

    Need Quick Garage Cost Info ASAP !!

    I got two quotes a few weeks ago on a 30x30 six inch deep for 10-11k. Another guy quoted me for the same concrete 18k. But the size he wants at 50x50 he should go 8 inches deep. And if I were doing this today go 14 H feet doors for heavy equipment.
  8. Alan J Odze

    [SOLD] BRAND NEW A833 SHIFTER KIT COMPLETE

    I bought a brand new Hurst Competition Plus shifter kit complete with Box, Rods, Clips, shifter w/ball, rubber boot (used) and trim ring (used) from LAYSON’s who got it from Brewers. Fits A Body A833 Trannies. My loss is you gain. $650.00 PAID 789 for shifter kit without the boot, ball, ring...
  9. Alan J Odze

    Need Quick Garage Cost Info ASAP !!

    Call this company. He does Cold Steel and Red Iron. Red Iron is more money. Look at the Cold Steel they use. Ask for Paul https://www.nationalsteelbuildingscorp.com/
  10. Alan J Odze

    Need Quick Garage Cost Info ASAP !!

    My advice is get a very good concrete guy and go at least 8 inch deep. I like either red Iron or Cold Steel. I have a red iron 30x45x18 and it’s too small. I don’t like these metal buildings that you see with weak interior walls. There was a tornado by me in upstate NY. A tree from a neighbor...
  11. Alan J Odze

    [SOLD] A833 HURST GEAR BOX SET

    Up for sale is a brand new never used Hurst shifter COMPETITION PLUS set for a A BODY 2 Door Bucket Seat. Includes three rods, mounting hardware, Hurst Shifter (used) ball and rubber boot (which is used) The Gear Box and Rods were never installed. As you can see I paid 789 just for the...
  12. Alan J Odze

    [FOR SALE] 1973 DODGE DART 340H CODE

    I forgot to add the engine came out of Trimboli’s 70 Cuda that he owned. Car has all new brakes front and rear, new calipers and pads, rear brakes, new McLoud Clutch and throw out bearing, 5 new tires and all new shocks.
  13. Alan J Odze

    [FOR SALE] 1973 DODGE DART 340H CODE

    I have a triple TX9 DODGE DART 340 H CODE DART FOR SALE. Reason selling it is I have too many injuries to enjoy this vehicle. The car was signed by Richie Petty. The engine is a Cuda 340 built by Steve Trimboli of Pit Bull Motors. The engine has a Purple Cam, Roller Rockers and built for...
  14. Alan J Odze

    Aftermarket shoulder belts for 68 barracuda convertible

    The Cuda is a 67 but should fit a 68.
Back
Top