Lee, do you still have the trunk floor for the 64 dart?

Good morning Lee, I was told to contact you by Sgrip65. He said you could help me out. I'm in need of an Uncut dash out of a 65 barracuda/dart/Valiant. I just need the metal dash and non A/c center trim piece, no gauges or other bits. let me know if you have anything please and thank you.

Lee, you were suggested to me by someone helping me find floor pans for a 65 Valiant. If you have anything or know of anything, I'd sure appreciate the help.

Lee, I noticed that you are parting out a '62 Valiant, and I just wondered if it has a Torqueflite, and if you might have a park lever knob in good condition that you would be willing to sell. Very hard to find, as it was a one-year-only part for the Valiant and Lancer.

Lee, These look like nice pieces('65 Valiant ). I am mainly interested in the crossmember for the torsion bars. If it's still available, let me know. Thanks alot

Lee, I'm hunting 66 valiant hardtop pieces. I'm missing all the pieces that have anything to do with the door window and 1/4 window seals mounting to the roof. Former race car allmthese pieces were removed years ago.

Hello, interested in the early a e brake cable. Can you send usps? Let me know how you would like to receive payment

Respectfully

Philip

Hi,I got your name from another member here in response to a post I ran about 65 Valiant 4 door quarters. Would you happen to know of any for sale.I'm going to use them on my 65 valiant wagon

Greetings, Lee. I saw your old post for the 1965 Dart dash, and that dash pad is a near-exact color match for me. Do you still have just the pad? monoloop@gmail.com is me. Thank you! - Peter C.

Looking for a power streering cap, Do you happen to have one or know where i can get one.
I have a federal pump i think, on a 65 273 commando Barracuda.
Thanks

Hello Lee
I would like your 74 Duster headlight bezels. How much shipped to 38135 Memphis Tn.?





Hello Lee
I would like the 2 1974 Duster headlight bezels> How much shipped to 38135 Memphis Tn? Do you accept pay pal? If not how do you want to be paid?
Thanks
big block

sent $70 lee, should be in your account

lee made a post on reply page, need your paypal address and shipping to 37752

Lee Do you have any 64 dart body's hanging around. If you do I need a piece of the body. Rear windshield left lower from where the curve ends one inch down one foot long. I believe its called the Dutchman panel.

Hi! I am looking for 68 dart 2d sedan drivers side door. Thanks

Do you have a list of 63 Valiant parts that you have on hand?

The air inlet for the 66 Valiant is great, thanks.
I know that you are not a free tech advisor but....
This is my first non-Ford. I am having a difficult time taking off the aluminum trim on the side. The shop manual shows the plastic clips and I can reach them from the inside but..... I can not get them to release. Any help or suggestions?

hello, did you have anymore front valances?

is the vents for 66 valiant ????/

Lee
I am interested in your frame rail for the drivers side of a 68 Barracuda. What would it cost to ship to zip 32046
Thanks

Never mind....I just saw your PM

Mr. Robinson
Remember asking you a while ago if you had any interest in the 64 valiant tub I have been slowly piecing out. Anyway, I might be bringing it to Sierra Vista, AZ (Joe Vega's)
and was wondering if you had any interest in it, I would lower the price somewhat if you had any interest in it. Would throw in rest of early A and probably rest of A (thru 76) parts if you wanted them. need to clean up yard, may be moving and or subleasing property eventually here in las Cruces area.
Dave
Dona Ana NM 88032
newmexguyus@yahoo.com
505-382-3022

HI Lee I am looking for the floor braces under the floor for 67 dart it has bucket seats front and rear on left and right side thank you

Hi Lee, I have a Barracuda 66 and I need some parts that you have, and I am interested to get them. And maybe you have some other parts that I can see. Thanks

GREAT GUY! Hooked me up with a K-frame. Thank you!

LEE this is Bob from ohio had bought some items from you in the past .i need a front license plate holder for a 1964 dodge dart . not bent, pretty nice. price with shipping to 44905 if you have it thanks picture would be nice