Recent content by Monstro_bjj

  1. Monstro_bjj

    Stop in for a cup of coffee

    Is there an exhaust manifold sequence for V8s (particularly the LA 360) ? Service manual only indicates torque specs for bolts....
  2. Monstro_bjj

    Another 360 question (or two)

    Once you get sealer on the studs for the water jackets, what’s the best way to tighten? I’m thinking hand tight is out of the question…
  3. Monstro_bjj

    Spring Fling 35 Apr 15 & 16, 2023 Van Nuys CA -info & roll call

    Any vendors on this thread that will be attending the Fling be selling hardware? Particularly exhaust manifold hardware? Didn’t know if this what the right place to ask. I was gonna order some but thought supporting our vendors was better .
  4. Monstro_bjj

    Engine and Trans Rebuild/Refresh in Los Angeles

    Hi All, Been wrenching on my first Mopar for about a year now and thinking about refreshing my motor and trans. I don’t think I need them rebuilt but since I’m not sure what’s been done, at least to the motor, would love to have a pro go through them and refresh everything (seals, gaskets...
  5. Monstro_bjj

    330 LED Bulbs (Fender Mounted Turn Signals)

    Hi Everyone, I recently bought LED “330” bulbs which are approx 1/4 long for fender mounted turn signals on my 72 Swinger. They obviously are too small and was looking for ones that are approx. 1/2 inch long to fit the factory fender mount turn signal socket (pictured). Anyone run into vendors...
  6. Monstro_bjj

    Light bulb chart

    Wanted to add to the thread: I added the above picture with the LED “330” bulbs which are approx 1/4 long. I was looking for ones that are approx. 1/2 inch long to fit the factory fender mount turn signal socket. Anyone run into vendors only selling these midget bulbs? Anyone know who sells the...
  7. Monstro_bjj

    New to FABO '69 Dart Swinger

    Very nice ride, sir! If I may ask, what type of wheels are you using?
  8. Monstro_bjj

    breather or oil cap?

    Yeah, it does have the bosses for screws. I'll look on Summit or look around other places. Thanks for the help!
  9. Monstro_bjj

    breather or oil cap?

    The covers I have, like the ones I showed before, do not have those baffles. Just checked. Wondering if those can be purchased?
  10. Monstro_bjj

    breather or oil cap?

    Gotcha. I was thinking of changing the style of breather to see if that would help with the oil issue but wasn’t sure if that would make a difference: Not sure what the underside looks like but there definitely isn’t anything like that already there.
  11. Monstro_bjj

    breather or oil cap?

    The valve cover has no baffle. The breather cap itself looks like it has a baffle but would have to look at it a bit more closely. It’s something very similar to this: Should I be using a different type of breather?
  12. Monstro_bjj

    breather or oil cap?

    Appreciate the knowledge. If I am getting some oil coming out of the breather, is a condition of a bigger issue? Just wondering, as that’s why I was thinking of closing that side off completely. Thanks again.
  13. Monstro_bjj

    breather or oil cap?

    Hi Everyone! I have Mopar valve covers that only have one opening per side. Knowing that I’m running a PCV valve on one side, should I use a breather for the other side (doubling as my oil filler) or should I use a closed off oil cap? I seem to be getting some oil blowback coming from the...
  14. Monstro_bjj

    Rally Wheel Cover Issue

    Sorry, I have a large bolt pattern. I’d have to check the size of the nuts to be totally sure if I’m running 3/4 or 13/16.
  15. Monstro_bjj

    Rally Wheel Cover Issue

    Hi Everyone, Has anyone run into an issue where the rally wheel covers get in the way of completely bolting down your wheels? I started to install my covers and noticed that the cover gets in the way of the socket I was using and also my tire iron. My tire iron is a lot “thinner” than the...
Back
Top