RedFish's Recent Activity

  1. RedFish replied to the thread 67 cuda hood.

    agreed. I call the long insert things inserts/medallions. I call the plated fish a badge.

    May 24, 2019 at 2:31 PM
  2. RedFish replied to the thread dodge dart rally dash questions.

    The difference is in how the dash is cut away for the different instrument panels to sit/attach in them. It might be possible to alter...

    May 24, 2019 at 12:24 PM
  3. RedFish replied to the thread 67 cuda hood.

    68 hood is the same sheet metal except with little turn indicators on it, holes to fill. The inserts/medallions are different but those...

    May 24, 2019 at 12:07 PM
  4. RedFish replied to the thread Universal Seat Bracket Use.

    Yep, crusty OEM tracks bring around 200 today... If you can find them. YouTube videos show how to take them apart and renew them. Good...

    May 24, 2019 at 9:47 AM
  5. RedFish replied to the thread Console clean up.

    One of my local paint store carries SEM products. It does cost more than some other brands found in part stores, Walmart, etc... Sems...

    May 24, 2019 at 9:36 AM
  6. RedFish replied to the thread Universal Seat Bracket Use.

    The inboard and outboard tracks are different heights. If my memory serves they have a little bit of front to rear ramp too. With all...

    May 24, 2019 at 9:10 AM
  7. RedFish replied to the thread Console clean up.

    I'll have to start at the beginning... my 67 buckets have steel backs with vinyl skin glued on them. Wrong kind of glossy spray paint...

    May 24, 2019 at 8:18 AM
  8. RedFish replied to the thread 73 spindles in my 67.

    73 up sway bar went through the middle of K and attached at a tab near the middle of lower arms length. Pre 73 sway bar went around the...

    May 24, 2019 at 7:00 AM
  9. RedFish replied to the thread [SOLD] 67 CUDA TRUNK PANEL CLIPS...nice! FINISH PANEL BarraCuda 1967.

    Not a completes set shown. 4 of inner fasteners required.

    May 23, 2019 at 9:03 AM
  10. RedFish replied to the thread 1969 A Body Console.

    See a little plastic plug in your upper door metal? The 67 model had a big chromed phillips screw head showing there. My point being,...

    May 23, 2019 at 7:59 AM
  11. RedFish replied to the thread Need help on wiring.

    Whether the ballast resistor is req'd or not depends on what coil was included. Some coils will operate on continuous 12 volts, others...

    May 22, 2019 at 10:38 AM
  12. RedFish replied to the thread Supplier for '68 Headlight switch?.

    F.Y.I. Aftermarket switches are later type so one size fits all. This means that the new switch will include a extra male spade terminal...

    May 22, 2019 at 10:33 AM
  13. RedFish replied to the thread Gas gauge always full (1968 Barracuda).

    first thing I would do is disconnect the fuel sender at the tank. If at ign' switch on the fuel gauge needle remains at home, the short...

    May 22, 2019 at 10:01 AM
  14. RedFish replied to the thread [WANTED] 1969 Barracuda Emergency Flasher Switch.

    If I can make a suggestion... wait until you're ready to put it all back together again. these panels are old and fragile. Already broke...

    May 21, 2019 at 3:31 PM
  15. RedFish replied to the thread 'interior interchangeability.

    1st generation bucket seat tracks are quite different form 2nd gen', wont work. We can't see what tracks are under those buckets but the...

    May 21, 2019 at 3:16 PM
  1. This site uses cookies to help personalize content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.