Treblig

Yes, I sill have it.

did you sell the B-body drivers side? # 3418621

Jason

I am interested in your manifolds do you have any for sale

Could you send me a PM (Conversation)??

afternoon sir, I have an 1971 dart swinger 318 9 to 1 comp. with 302 casting # heads ,the heads are off an middle 80'3 p.up I would like manifolds with large openings ,I have the smaller ones now. Just discovered you, any help or if you have for sale I am interested

The 70s driver 340 paired with a magnum 360 would fit perfect. I have one pair left. Sent PM please.

What are the best fitting manifolds for a 360 in a 73 Dart Swinger? Do you have any and how much would the cost be.

Your inbox is full, lots to explain. Please clear your inbox and start a conversation. Gil

Hi treblig ,I have a 65 dart 273 with manual steering and Air if i swap a 73 340 will these manifolds fit ?

Sorry, but I only have 340 manifold pairs and no single driver's side manifolds.

thanks//will be working long hrs until Monday(day off)/will monitor msgs on and off

in the market for 340hp #2863553 and 2863549 exhaust manifolds/descent driver side heat sheild ??do you take pay pal ??

Hey Treblig, I'm looking for the right side exhaust manifold with the large opening, it looks like you only have the left? Do you know where I could get a right side for my 66 valiant?
Thanks,
Kevin

Gil:

Sorry, it limited my characters. 318 magnum in a 67 Barracuda. I have some Ram manifolds and Grand Chrokee manifolds. Both look like they interfere with the power steering box. Have not physically tried yet.

-Dave

I have a question. I have a small block using 273 manifolds attached to an AX15 transmission. This transmission uses a 143 tooth flywheel, which places the starter farther out. My current manifolds dump the exhaust right between the torsion bar and starter where there is only about 1" clearance (had to squish the pipe to fit). Is there a driver side manifold that exits farther back?
-Dave Belau

I have very few parts left over. Can you be more specific??

Do you have any 68 fenders?? or 67 parts , I just met a guy at the gas station up here in wisc , I had my 65 Barracuda out and he came over to talk about them and he is from Aimes Iowa he was goung to send me all his info tohelp him find some parts thanks Jon HAGR812

Need to see if I have any more 340 manifolds. I received 4 orders in just 2 days. Give me a little time to get back with you.Thanks Gil

I am in the same boat as lawman340. 72 Scamp, 318, stock heads (for now) and am interested in the 340/360 combo. 904 trans, column shift, power steering. Same questions as him. Thank you.

I am interested in your 340/360 manifolds, I have a 72 scamp automatic on the column stroked 318 with power steering....will they fit ? Cost? Deposit required and how to pay, thanks, Chris. c.depute.210@gmail.com

Was reading your response to the question regarding how far in the hole pistons were in 68-69 318's.

I'm getting ready to put a set of 302's on my 69 318. Just wondering if you experienced any issues and if the performance was noticeable?

Thanks for any feed back

I would like to see a pic of the manifolds you make for a valiant,Where i put a 273 in it.

Hi Gil. Msg w/you a while back about the 340 manifolds. Ready to order a pair if you're still doing/have them. I'm thinking the 70's 340/machined 360 set would work best for me as this is a 73 340 Duster. As long as I end up w/the 2 1/4 outlet. I'll also need a set of stub pipes. I'd prefer the dark grey finish if possible. The car is an automatic in case this will create a problem. You required a $200 deposit for a place in line which is fine. Please let me know if you're still doing this w/an address and the method of payment you prefer. Thanks for your time. Jeff

Hi Treblig, jbc426 here. I had an issue with my 200R4 falling out of lock-up once warm. Turns out this is not too uncommon of a problem, subsequently Sonnex makes a repair kit for it that uses a Teflon piston ring and a new plunger that is actuated by the TCC valve. Just thought you might be intereste in the info.

Aside from that, I am sure loving this 200R4 swap. best thing I ever did for the car.
John

Hi Gil. Just getting around to putting my new engine in my 67 Barracuda. I am in need of a 340 drivers side exhaust manifold. Do you have any left? If so, what is the cost? If you can give me a call that would be great. Ben 405-274-2582