dirt track'in a A-body

heres the class rules,..its a all chevy show,..wanta teach them bout mopar-mobiling!!

2013 Renegade-V8 Division Rules

1. BODY - Any full/mid size American made car or truck. No jeeps, 4x4?s,will be allowed to run. WHEELBASE min. is 101'' with a 1'' tolerance. 6'' REAR SPOILERS ok 6''. (side spoilers ok.) Doors, fenders and quarter panels may be fabricated of steel or aluminum, but must be stock appearing. Must have steel OEM roof. Floor pans must be in stock location... Trunk pans may be cut out . Firewall must be stock and in the stock location,or steel in stock location....

2. CHASSIS - Uni-bodies may be tied together. Hulling is legal. Must have a full roll cage constructed of a min. 1 1/2'' tubing.

3. Front inner fender wells may be removed. Fender wells may be cut for tire clearance.

4. Fuel cell is mandatory. Safety belts, harness and fire extinguisher mandatory. Must be track approved.

5. FUEL - Racing fuel ok.

6. WEIGHT - 3300 lbs.

7. SUSPENSION - Must be stock and in the stock location. May run racing springs. No Chrysler rear leaf springs on GM chassis. Front springs may be changed and non-adjustable buckets ok. Spring shackles ok. Upper A-frame may be cut for caster. Non-adjustable tubular upper A-arms ok. FRONT Shocks must be in the stock location.REAR shocks may be relocated.
SHOCKS MUST BE STEEL BODY.....

8. TRANSMISSION - Factory OEM manual or automatic ok. NO Bert, Brinn, Jericho or direct drives. Automatics must have a working torque converter. FLYWHEEL must weigh 14 lbs min. CLUTCH-stock type pressure plate and clutch disc of 10 1/2'' min. Steel scatter shield mandatory with manual transmission, may be fabricated from 3/16''steel and track approved. factory slave hydraulic release cylinder ok. after martket hyd release bearing allowed

9. REAR END - Posi-track, limited slip, or locked rear ends ok. Mini-spool ok. 9" Ford in all cars ok for safety. Aftermarket axles ok
.
10. BRAKES - 3 wheel working brakes mandatory. No brake adjusters.MAY USE RIGHT FRONT SHUT OFF..

11. TIRES - Any 8 inch max dot or racing tire UNTOUCHED,that punches a min of 60 anytime they are checked....NO soaking,grooving,siping,etc....

***Also imca modified and ndra modified tires also legal that punch atleast 60 or harder and must remain UNTOUCHED

12. WHEELS - Steel only, 8'' wide max. Bead lock, beadlock on Right side only. Large wheel studs recommended. NO WIDE FIVE HUBS/WHEELS

13. DRIVE SHAFT - Must be painted white with car # on it. Must have a safety loop 8?-12? to rear of transmission where drive shaft inserts into transmission.

14. ENGINE - Must be in front of stock (or steel) fire wall with fire wall (or steel) being in stock location and be stock for make and model of vehicle. RODS - OEM stock steel rods for engine used. Stronger rod bolts may be used. Polishing, stress relieving, balancing and floating pins are optional. MAX. OVERBORE IS .060?, 0? deck ok. CUBIC INCH - GM & FORD 365 cubic inch max. Chrysler 374 cubic inch max. If crossmember is notched to clear fuel pump you must add an extra 50lbs in front of motor.... OIL PAN must have inspection plug above baffles 2" prefered 1" min....

15. CAM & LIFTERS - .425 hydraulic max. with 0 lash. No rollers. Anti-pump up lifters ok. Must be stock lifters for engine.

16. HEADS - Stock OEM straight plug cast iron heads only No less than 70 CC.. No closed chamber (high performance heads) such as 461, 461x, 041, 186, or 492 castings. No vortex or angle plug heads. Screw in studs and guide plates ok. VALVE SPRINGS - Stock diameter single valve springs (1.250'') and stock rocker arms for the engine used. No hand blending. VALVES - Steel only. Max. size 1.94 intake, 1.5 exhaust.

17. INTAKE - Stock cast iron intake for engine used. May run aluminum performer #2101 (not the rpm version) with Holley 600 #1850 carb or Holley 500 # 4412 with 1'' max. spacer plate. No bowtie or Brezenski intakes. HEADERS - ok.

18. PISTONS - Stock type OEM or replacement type (no lightweights). Must have 4 valve reliefs or dish type only.

19. CRANKSHAFT - Stock OEM only. Stock stroke only. GM is 3.48'' only. Must have GM part #. May be balanced. No knife edging. CAST 48 lbs. min. STEEL 50 lbs. min.

20. IGNITION - Stock type only. HEI ok. Brass dist. gear ok. COIL - Any. NO MSD.

21. FUEL PUMP - ANY

22. CARBURETOR - Holley 600 #1850 (out of the box) may run performer aluminum intake #2101 with 1'' max. spacer plate. Holley 600 may remove choke and re-jet. Max. throttle bore is 1 9/16''. Max. venturi size: primary is 1.250'', secondary is 1 5/16''. Holley 500 #4412 may run 1? max. spacer plate. Max. throttle bore is 1.6875''. Max. venturi size is 1.375''. QUADRA-JETS OK, but must run stock OEM CAST IRON intake. NO BOW-TIE intakes. There will be a $300 buyout rule for any carburetor..