What Are You Doing To/With Your Car Today?
- Thread starter MobileCustoms
- Start date
-
Doh! sorry. I generally try to link to and/or post the part numbers I use.
Artec Industries Battery Boxes OP3405
Dusterdenovo
Contentedly Old School
Installed the Radiator, ATF Cooler and Clutch Fan assembly.
Had to massage the tabs on the hub of the Derale 17118 to make it fit over the base of the clutch (Hayden 2947). In the picture, the tab at 3 oclock hasn't been touched yet; the other 3 are 'tuned up'.
Next step: getting all of the plumbing put together.
Had to massage the tabs on the hub of the Derale 17118 to make it fit over the base of the clutch (Hayden 2947). In the picture, the tab at 3 oclock hasn't been touched yet; the other 3 are 'tuned up'.
Next step: getting all of the plumbing put together.
73 Swinger 8
Well-Known Member
Changed the valve stem on my front tire, and removed my master cylinder. New one should be here tomorrow.
I like the bracket you fabbed up for the ATF cooler. Much better than the little mount-it-to-the-radiator like I did. post #1907, page 77
Today I did a little rust repair and built a drivers wheelhouse. Prepping to hang a quarter.
mario03srt
Well-Known Member
All,
Last week added a set of MSD 8.5mm Superconductor Wires and a 4" KN Air filter. I squeezed it in with the AirGap Mani and a 1/2 inch spacer on the FiTech. This week ordered and received my 11.75 rotors and Dr. Diff Brackets, also received my Right Stuff Rear Disk conversion kit!!! Started cleaning and painting the rotors and calipers. I will swap out the stock front rotors/brackets on Saturday. The rear is going to wait till XMas break as it will take a bit more work.
Marion
Last week added a set of MSD 8.5mm Superconductor Wires and a 4" KN Air filter. I squeezed it in with the AirGap Mani and a 1/2 inch spacer on the FiTech. This week ordered and received my 11.75 rotors and Dr. Diff Brackets, also received my Right Stuff Rear Disk conversion kit!!! Started cleaning and painting the rotors and calipers. I will swap out the stock front rotors/brackets on Saturday. The rear is going to wait till XMas break as it will take a bit more work.
Marion
toplscuda
Well-Known Member
Finished up getting the quarters installed and went back and repaired the drivers side striker that I overlooked before installing the panel. I have never run across one where the post washer was broken in several pieces. Now to find a replacement
I was putting some summer things away in the storage garage and I had to get my 66 Dart out anyway might as well take it for a drive.
California weather, gotta love it. First of December in Iowa and no snow yet. I'm loving it. I didn't even use the heater. LOL
loganscuda
This/These
ScampMike
Despicable Damn Yankee
63 = winter = jacket - - THAT is hilarious!!!
Installed a new water temp sensor in the parking lot last night after work. I couldn't do it at lunch because, Coldstone Ice Cream...
https://www.amazon.com/gp/product/B073BX812V/?tag=joeychgo-20
https://www.amazon.com/gp/product/B073BX812V/?tag=joeychgo-20
MobileCustoms
Well-Known Member
Got the front suspension done! -mostly...
Installing new bucket seats in my van so that I can drive seat belted in and continue breaking in the engine vs. sitting on the wheel hump!!
Oh, and secure the glovebox door somehow to keep it from flipping open when doing test launches, and also removing everything that's not secured in the van to prevent it all from being thrown back to the rear...
Oh, and secure the glovebox door somehow to keep it from flipping open when doing test launches, and also removing everything that's not secured in the van to prevent it all from being thrown back to the rear...
Today's winner!Installing new bucket seats in my van so that I can drive seat belted in and continue breaking in the engine vs. sitting on the wheel hump!!
Jeff
Dusterdenovo
Contentedly Old School
Decided on the color scheme for my AN Hoses and fittings, plumbed in my ATF Cooler.
Russell's suggestion of cutting the braided hose with a hacksaw was a FAIL, but wrapping the hose tight with about 4 wraps of masking tape and taking a cutoff wheel to it brought SUCCESS.
Russell's suggestion of cutting the braided hose with a hacksaw was a FAIL, but wrapping the hose tight with about 4 wraps of masking tape and taking a cutoff wheel to it brought SUCCESS.
Sir, would you be willing to share the brand of trans cooler. Thanks
-
