what you think???

any good ?

  • Nope... staying away

    Votes: 12 44.4%

  • Sounds good to me

    Votes: 0 0.0%

  • nice but too expensive

    Votes: 15 55.6%
  • Total voters
    27
-
I think I would tell them to not put any brake line on it and do my own with over the counter double flare. That nickel plated by the roll crap is notorious for low abrasion resistance. Long term contact with hard plastic will wear a hole through it, the steel retainer straps on the axle tubes will do it in very short term. Not to mention they don't even use a radius tubing bender to form it. Makes me wonder what else is hiding under that shiny black "powder coating"...
 
Looks awesome but that is to rich for my blood. Imo there are alot of strong options for alot cheaper.
 
A custom width Strange 60 is $250 cheaper if you add your own brakes and spring perches? Nothing amatuerish about this one.
S60-Front-Leaf.jpg
 
BrianT said:
A custom width Strange 60 is $250 cheaper if you add your own brakes and spring perches? Nothing amatuerish about this one.
View attachment 1715299638
Click to expand...

If I remember right, I gave $2100 plus shipping for my dana 60, !" narrower than A body width, disc brakes, 3" studs, Detroit locker , 3:73 gears, had to make my own brake lines and emergency brake cables.
 
That’s the free market at work.
A person is putting their best on a pallet with a fork lift and selling what they built.

Nice thing is we can grab a bowl of pop corn and sit back and wait for the results.
Honestly- from pictures other than cheap Chinese rubber brake line and copper clad metal lines (easy to bend material but low abrasion resistance. ) it looks good but time will tell.
 
I think I would have found another picture of the gears to post that pattern is pretty high on the tooth, might not make noise but you never know.
 
brian6pac said:
I think I would have found another picture of the gears to post that pattern is pretty high on the tooth, might not make noise but you never know.
Click to expand...

Yep, that's a tooth chipping pattern even if it didn't make noise, but I'd bet it will.
The contact area shouldn't touch the edge of the gear teeth anywhere or it will chip the teeth and eat itself.
 
This was 3k something to my door from strange and it's got every bell and whistle you can buy.

dana1.jpg
 
$120 Craigslist truck Dana (came with good 4.10's) about $600 or so to dr.dif... spool, bearings, axles, ect.. $175 gear set up, and $300 or so to professional welding. Use my 8 1/4 break stuff. Total..
$1200...
20160123_111320.jpg
20160123_115207.jpg

20160514_182044.jpg
 
looking at the "workmanship" of the brake line, i wouldnt touch it
 
I been trying to get a good pic of my rear end but it's not easy. It just looks like a skinned chicken hanging from two hams...
 
Cope said:
I been trying to get a good pic of my rear end but it's not easy. It just looks like a skinned chicken hanging from two hams...
Click to expand...
I respectfully pass, I don’t even want to see my own anymore...
 
Wait for it.....






















Bam!

And you all thought it was gonna be a pic of the Frank and beans... you sick bastards....

20181121_152702_zpshmblnxws.jpg



Just under 3 grand for this and it has all the bad *** parts.
 
Bwahahaha! I got *** end envy now, that’s a lot better than 7-1/4 pile I got under the back of mine... come to think of it, an axle out of a decent UTV side X side is stronger.
 
You must log in or register to reply here.
-

Back
Top